665-12793K311 Parts

The Arm-Spray is an OEM part for Whirlpool brand dishwashers. It is the rotating spray arm assembly responsible for dish coverage during wash cycles.

Causes of a bad spray arm include mineral buildup that causes clogs, wear and tear of the bearings that allow rotation, or physical damage from loads. 

Symptoms of a bad spray arm involve:

• The inability of the arm to rotate smoothly during cycles
• Gap coverage of water and detergent along the dish racks  
• Abnormal noises coming from the arm area
• Decreased cleaning effectiveness on dishes

This Whirlpool replacement part is also compatible with KitchenAid, Jenn-Air and some Kenmore models.

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This torsion door hinge spring provides counterbalance and smooth pivot action for a refrigerator door, helping the door open and close evenly and remain in the correct position. It replaces a worn or broken hinge spring to restore proper door operation. What it does:

• Applies torque at the door hinge so the door stays balanced and closes reliably
• Reduces sagging or uneven door movement caused by a weak or broken spring
• Helps prevent gaps that allow warm air in or cold air out
• Works with the hinge assembly to keep doors aligned during use

• High-level replacement: remove door or hinge trim before swapping spring
• Support the door during removal and installation to avoid dropping or damaging the cabinet
• Disconnect power if working near electrical components; follow OEM safety guidance

This 9/32" ratcheting retainer secures mating components in place, providing a reliable spring-lock connection that resists loosening from vibration. Use it to restore proper fit where the original retainer has worn or broken. What it does:

• Holds shafts, rods, or assemblies securely in position using a ratcheting/spring clip action
• Prevents side-to-side movement and reduces rattling or misalignment
• Commonly replaced when the original clip is bent, cracked, or no longer grips tightly
• Works as a direct-fit replacement to restore intended component retention

• Basic hand tools may be required; handle the clip carefully to avoid pinching
• Wear eye protection—spring clips can release suddenly during removal/installation
• Ensure mating parts are aligned before seating the retainer for a secure fit
• If other fasteners or damaged parts are found, inspect and replace as needed

This small retainer clip secures trim and components to keep panels, hoses or assemblies in place so they don't shift or rattle during normal use. It's a simple replacement when a worn or broken clip lets parts move. What it does:

• Holds appliance trim, panels or small assemblies securely to their mounting points
• Prevents rattling, vibration or misalignment caused by a loose fastener
• Restores proper fit where a broken or missing clip allows parts to shift
• Works wherever the OEM diagram shows this clip as the retainer for the targeted component

• Disconnect power and water before beginning any repair
• Use the OEM diagram to locate the clip and correct orientation
• Remove surrounding trim or fasteners as needed; pry or press clip into place per diagram
• Replace damaged clips with the exact part number for proper fit and function

This outlet cover assembly replaces a damaged or missing outlet cover on compatible Whirlpool appliances, protecting the outlet opening and helping maintain proper airflow and appearance. What it does:

• Covers and protects the appliance outlet opening from debris and accidental contact
• Helps maintain correct airflow paths for the appliance cabinet
• Restores the finished appearance of the appliance where the original cover was cracked or missing
• Common symptom: visible crack, broken tabs, or missing cover around the outlet opening

• One outlet cover assembly

• Install with the appliance powered off and unplugged or with circuit power disconnected for safety
• Typically secures with snap tabs or a small number of screws; inspect mounting points before installation
• Handle carefully to avoid breaking plastic mounting tabs; replace any damaged fasteners

This thermostat bracket secures the refrigerator/freezer temperature sensor or thermostat to the cabinet, keeping the sensor in the correct position for accurate temperature control. Durable replacement for factory mounting hardware. What it does:

• Holds the thermostat/temperature sensor in place so it reads interior temperatures correctly
• Helps prevent loose or misaligned sensors that can cause irregular cooling or cycling
• Restores proper sensor positioning after damage or broken mounting clips
• Works with the thermostat assembly to maintain consistent appliance operation

• One thermostat mounting bracket

• Disconnect power to the appliance before service to avoid electrical shock
• Handle thermostat/sensor elements carefully; avoid bending or pinching the sensing tube
• Retain or reuse original fasteners unless replacement hardware is explicitly included

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

This torsion door spring helps counterbalance and control the front door movement for proper opening and closing, restoring smooth, even door action and reducing door sag or uneven alignment. What it does:

• Applies rotational tension to the front door hinge to help the door stay open or close gently
• Helps prevent door droop, misalignment, and binding during normal use
• Works as part of the hinge/torsion assembly to maintain correct door balance
• Common symptom: door feels heavy, drops, won't stay open, or closes too quickly

• One front torsion door spring

• Disconnect power to the appliance before beginning work and follow all safety precautions
• Torsion springs are under tension—use proper tools and caution
• Follow manufacturer service manual or OEM instructions for correct orientation and torque

This display lens is the clear plastic cover that protects and improves visibility of the appliance control panel. It restores a clean, readable look and shields the underlying display from scratches, spills, and wear. What it does:

• Protects the control board display window from damage and everyday wear
• Helps maintain clear visibility of LED/console indicators and touch areas
• Replaces cracked, cloudy, or scratched lenses that obscure controls
• Keeps moisture and debris away from the electronics behind the panel

• Disconnect power to the appliance before beginning any repair
• Console or trim panel removal is often required; handle clips and tabs carefully
• Use non-marring tools to avoid scratching the new lens during installation

Color: Black

This jumper wire connects control board circuits at the range/oven control panel to restore proper panel signaling. It's a simple replacement that helps resolve intermittent or missing control responses caused by a broken or damaged jumper. What it does:

• Bridges specific control panel terminals to complete circuit paths between the user interface and main control
• Restores continuity when an existing jumper is cracked, corroded, or broken
• Helps eliminate intermittent touch/control pad failures or non-responsive buttons linked to a faulty jumper
• Small, direct-use part for electronic control troubleshooting

• One jumper wire as shown

• Disconnect power to the appliance before servicing to avoid shock or damage
• Access may require removing the control panel or console—follow OEM service instructions
• Handle wiring and connectors carefully to avoid bending pins or damaging the control board