66512769311 Parts

This thermostat bracket secures the refrigerator/freezer temperature sensor or thermostat to the cabinet, keeping the sensor in the correct position for accurate temperature control. Durable replacement for factory mounting hardware. What it does:

• Holds the thermostat/temperature sensor in place so it reads interior temperatures correctly
• Helps prevent loose or misaligned sensors that can cause irregular cooling or cycling
• Restores proper sensor positioning after damage or broken mounting clips
• Works with the thermostat assembly to maintain consistent appliance operation

• One thermostat mounting bracket

• Disconnect power to the appliance before service to avoid electrical shock
• Handle thermostat/sensor elements carefully; avoid bending or pinching the sensing tube
• Retain or reuse original fasteners unless replacement hardware is explicitly included

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

The Lower Door Seal is an OEM replacement part for Whirlpool dishwashers. This seal runs along the bottom edge of the dishwasher door, creating a tight seal against the tub when closed to contain water inside during cycles.  This seal measures approximately 22 inches in length

Causes of lower door seal failure commonly involve repeated compression stresses from opening/closing actions gradually stiffening the flexible gasket material. Drying out and cracking occurs over years of heat exposure as well.

Symptoms of a worn lower door seal include:

• Water leaking out from beneath dishwasher door during cycles
• Difficulty latching door completely from warped seal edges  
• Visible cracks, splits or brittleness along the length of the seal
• Gaps allowing water intrusion beneath door perimeter

This versatile OEM part is also compatible with select Maytag, KitchenAid, Jenn-Air, Amana, and some Kenmore dishwasher models.

The Diverter Motor is an OEM part for Whirlpool dishwashers controls the diverter valve, which directs water flow to various spray arms throughout the dishwasher during a wash cycle. By accurately adjusting the flow of water, the diverter motor ensures that dishes are thoroughly cleaned and rinsed by optimizing coverage and water intensity according to the cycle selected.

Causes of a bad Diverter Motor can include electrical failures, mechanical wear over time, or damage from water infiltration.  

Symptoms of a bad Diverter Motor include:

• Dishes not being cleaned properly due to insufficient water reaching all areas.
• Unusual noises coming from the dishwasher, which may indicate a struggling or stuck diverter motor.
• Error codes displayed on the dishwasher that are related to water distribution functions.
• Leakage from the dishwasher base 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This box cover protects and conceals the appliance's electrical junction box, keeping wiring secure and reducing exposure to dirt and moisture. It restores a finished appearance and helps maintain safe electrical connections. What it does

• Shields the junction box and wiring from dust and debris
• Helps prevent accidental contact with live terminals
• Maintains the appliance's original fit and finish around electrical components
• Commonly replaced when the cover is cracked, missing, or damaged

• One box cover

• Disconnect power to the appliance before installing to avoid electrical shock
• Handle carefully to avoid damaging tabs or screw bosses used for mounting
• Use the OEM screws or fasteners; replace missing hardware with manufacturer-recommended parts

This plate-latch strike secures the appliance door by engaging the latch assembly so the door stays closed during operation. It replaces a worn or damaged strike to restore proper door closure and reliable operation. What it does:

• Provides a sturdy contact point for the door latch to engage and hold the door closed
• Helps prevent the door from popping open during use, which can cause cycle interruption
• Addresses symptoms like a door that won't stay latched, won't close fully, or causes the unit to stop mid-cycle
• Works as the mating strike for the existing latch assembly to ensure proper alignment

• One plate-latch strike

• Disconnect power to the appliance before beginning any repair
• Access the strike by opening the door; remove any trim or screws as needed to reach the strike mounting location
• Install replacement in the same orientation as the original and tighten fasteners securely without over-torquing
• After installation, verify the door latches smoothly and the appliance completes its normal cycle

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit

A small metal spacer plate used to position and support nearby components for correct alignment and clearance. Replaces a worn or missing spacer to restore proper fit and reduce rubbing or vibration. What it does:

• Holds components at the correct distance to prevent contact or interference
• Maintains alignment of panels or assemblies for reliable operation
• Helps stop vibration-related noise caused by loose or misaligned parts
• Preserves sealing/fit where precise spacing is required

• Disconnect power before servicing to avoid shock or injury
• Handle sharp sheet-metal edges carefully and wear gloves
• Install in the same orientation as the original; secure with the factory fasteners
• Do not force or overtighten fasteners—ensure proper alignment before fully torquing