66513266651336 Parts

This small retainer clip secures a light assembly or lens so it stays firmly in place during normal operation. Replacing a worn or missing clip helps prevent loose covers, rattles, and poor light positioning.

• Holds the light lens or fixture securely against its mounting surface
• Helps maintain proper alignment for consistent illumination
• Replaces broken, bent, or missing hardware
• Common fix for a loose or falling light cover or a vibrating light assembly

• Disconnect power to the appliance before servicing
• Allow hot surfaces and bulbs to cool before working near the light area
• Support the lens/fixture while removing the old clip to prevent dropping
• Ensure the new clip seats fully and the light assembly is secure before restoring power

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The feed tube assembly routes wash water up the back wall of your dishwasher to the upper spray system, restoring balanced spray pressure and coverage on the upper rack when the original tube is cracked, warped, leaking, or obstructed. What it does:

• Directs water from the circulation pump to the upper spray system via the rear manifold/docking port
• Maintains a sealed path to prevent internal leaks and pressure loss
• Damage or clogs can cause poor top-rack cleaning, weak spray, noisy operation, or residual detergent
• Visible cracks, broken tabs, or leaks at the rear wall indicate replacement is needed

• Feed tube assembly

• Disconnect power and shut off the water supply before servicing
• Open the door and remove racks as needed; release screws/clips securing the rear feed tube and detach from the docking port
• Transfer any reusable seals or brackets; align and secure the new tube without overtightening plastic fasteners
• Run a short cycle to check for leaks and proper upper-spray operation

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.

The Screw is an OEM part compatible with Whirlpool dryers. This screw connects the back panel to the side panel, ensuring the dryer cabinet is securely assembled. It plays an integral role in maintaining the structural integrity of the dryer housing.

Symptoms of a bad screw can include loosening, corrosion, or breakage over time and use. This can compromise the bond between panels and weaken the overall dryer frame.  

Causes of a bad screw include:

• Repeated expansion and contraction from heat cycles  
• Vibrations loosening the connection point
• Stress or cracks developing at the screw head or threads

These issues can lead to:

• Gaps appearing between panels
• Components like controls detaching from the housing
• Cabinet unable to withstand pressure changes  

This OEM Whirlpool replacement screw is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This is a 10-32 threaded machine screw used to fasten appliance panels and components securely. It restores proper fit and prevents rattling or loose parts when a missing or stripped fastener causes instability. What it does:

• Fastens panels, trim, brackets, and internal components that use 10-32 threads
• Restores secure fit when a missing or damaged screw lets parts shift or vibrate
• Helps eliminate rattling, loose connections, and alignment issues caused by lost hardware
• Works where a standard 10-32 machine screw is specified by the manufacturer

• Disconnect power and gas before accessing internal components
• Use the correct screwdriver or nut driver to avoid stripping the head
• Do not overtighten; snug until secure to avoid thread damage
• Keep removed hardware for reference and replace only with identical thread size

This small retaining clip secures trim and appliance components to keep panels and assemblies in place, helping prevent rattling and loose parts during use. It's a simple replacement that restores proper fit and alignment. What it does:

• Holds panels, trim, or small assemblies in place to maintain a secure fit
• Prevents rattling, vibration noise, and movement of loose parts
• Replaces broken, bent, or missing clips that allow gaps or misalignment
• Works where a small fastener is needed to secure plastic or metal components

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area for damage; replace any broken mating tabs or screws for a secure fit
• Installation typically requires basic hand tools such as pliers or a screwdriver; apply steady pressure to snap clip into place

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This dispenser cover is the replacement lid for a washer dispenser assembly, restoring a secure, functional cover that keeps detergent and fabric softener contained until the wash cycle. It helps prevent spills and keeps the dispenser looking finished. What it does:

• Replaces a cracked, warped, or missing dispenser lid so the dispenser closes properly
• Helps contain detergent and softener to prevent drips and spills onto the washer top
• Restores a flush, finished appearance to the dispenser area
• Works with the dispenser housing to ensure proper release of cleaning agents during cycles

• Disconnect power and water supply before servicing the washer
• Replacement typically installs with clips or screws; keep original fasteners and note their placement
• Handle plastic parts carefully to avoid cracking; align tabs before snapping into place