66517609 Parts

This standpipe houses the washer's overfill control and directs excess water into the drain path, helping prevent overfilling and internal flooding. It's a direct-fit replacement for the factory overfill control housing. What it does:

• Provides the sealed channel for excess wash water to flow to the drain
• Supports and locates the overfill/level control assembly
• Helps stop water from overflowing the tub and causing leaks
• Can resolve symptoms like unexplained overfilling, water leaking at the washer base, or fill-level issues

• Disconnect power and shut off water before starting any repair
• Access may require removing the washer top or control housing
• Inspect surrounding gaskets and hoses for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; test operation after reassembly

A threaded screw used to secure appliance components where an 8-16 thread is specified. Provides a straightforward replacement fastener to restore original fit and keep panels, brackets, and internal parts held securely. What it does:

• Fastens panels, brackets, trim, and small assemblies that use an 8-16 threaded fastener.
• Replaces missing, corroded, stripped, or damaged screws to stop rattling, gaps, or loose parts.
• Restores reliable mechanical connection after service or part replacement.
• Compatible where the OEM specifies an 8-16 screw for mounting or securing components.

• Use the correct driver to avoid stripping the head; start threads by hand to prevent cross-threading.
• Tighten until secure but avoid over-tightening to prevent damage to mounting holes or plastic parts.
• If working near electrical components, disconnect power and follow all safety precautions.
• Inspect mating threads and replace if damaged before installing this screw.

This sump tab secures the dishwasher's sump assembly to the tub opening, keeping it properly aligned and sealed. Replace a broken or missing tab to address movement, rattling, or leaks originating from the sump area.

• Locks the sump assembly to the tub/base opening
• Helps maintain the sump-to-tub seal to limit leaks
• Keeps the pump intake and fine filter area properly positioned
• Common symptoms: leaks under the unit, loose/shifted sump or filter, rattling/vibration from the sump area

• Disconnect power and water supply before servicing
• Access the sump per your model (from inside the tub by removing lower rack/filters, or from below after removing the toe panel)
• Ensure the sump and gasket are fully seated; install the new tab until it locks securely
• Run a brief fill/drain test and check for leaks before reassembly

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This is a genuine 4-24 x 3/8 screw used to fasten trim and components on compatible appliance assemblies. It provides a secure, vibration-resistant connection so panels and parts stay properly aligned during use. What it does:

• Secures panels, brackets, or components to the appliance frame
• Helps prevent rattling or loosening from normal vibration
• Works with threaded or self-tapping holes sized for a #4-24 fastener
• Common replacement for stripped, rusted, or missing mounting screws

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread damage
• Replace any corroded or damaged screws in sets when multiple fasteners show wear
• Disconnect power and follow appliance safety guidance before servicing

This inlet fill hose directs incoming water from the household supply to the washer's tub or dispenser so the appliance fills properly. Replaces a damaged, cracked, or leaking fill hose to restore normal water flow. What it does:

• Carries water from the home supply to the washer fill valve and dispenser
• Helps the washer fill to the correct level for cycles
• Commonly replaced when you see leaks, visible cracks, or reduced fill flow
• Prevents water damage from split or worn hoses

• Disconnect power and shut off the water supply before servicing
• Inspect hose fittings and clamps; replace worn clamps and tighten securely
• Avoid sharp bends or kinks when routing the hose
• After installation, turn on water and check all connections for leaks before use

This folddown pivot is the lower hinge that lets a folddown door or panel rotate smoothly and hold position, restoring proper movement and alignment. It replaces a worn or broken lower pivot so the door or panel opens and closes correctly. What it does:

• Acts as the lower hinge point for a folddown door or panel, allowing controlled pivoting motion
• Replaces a worn, cracked, or broken pivot that causes sticking or sagging
• Helps the door/panel stay aligned and close securely instead of dropping or binding
• Commonly used when the folddown component wobbles or will not stay in the open or closed position

• Disconnect power and remove any attached panels or shelves before replacing
• Support the door/panel during removal and installation to avoid damage or injury
• Reuse OEM fasteners if undamaged or replace with equivalent hardware; ensure proper alignment during installation
• Test movement several times after installation to ensure smooth operation and secure fit

This wheel and bearing assembly mounts to the upper dishrack, allowing it to glide smoothly in and out on the rail. Replacing a worn or broken wheel restores smooth operation and helps keep the rack securely on track.

• Supports and guides the upper rack along the side rails
• Restores smooth rolling and proper rack alignment
• Helps prevent the rack from binding or derailing
• Common symptoms: rack hard to slide, falls off track, wheel cracked/missing, squeaking or grinding as the rack moves

• Disconnect power before servicing; remove the upper rack from the rails by releasing the rack stops
• Release the old wheel/bearing from the rack tabs and remove
• Snap the new assembly into the rack mounting holes until it locks
• Reinstall the rack and verify smooth travel on both rails

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

For spray arm seal use WP8268340.

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

This bezel vent deflector covers and directs dryer exhaust while keeping the vent opening neat and protected. It restores proper airflow path and prevents clothes or lint from catching on the exhaust opening. What it does:

• Guides exhaust air from the dryer to the vent outlet for better airflow
• Protects the vent opening from snags, debris, and visible wear
• Helps reduce lint escape at the cabinet opening and keeps the area tidy
• Replaces cracked, warped, or missing vent bezel that can affect exhaust performance

• One bezel vent deflector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the vent area per your model's service instructions (rear or front panel removal may be required)
• Align tabs/clips and press into place; replace any broken retaining clips or screws as needed
• Clean the ductwork and lint trap before reinstalling