750B Parts

A replacement refrigerator door gasket that restores the door seal to help maintain proper cooling and energy efficiency. Replaces torn, cracked, or hardened gaskets to reduce warm air leaks and moisture buildup. What it does:

• Seals the refrigerator door to keep cold air inside and warm air out
• Helps reduce frost buildup and prevents moisture from entering the compartment
• Supports consistent internal temperature for better food preservation
• Stops drafts and improves compressor efficiency when sealing properly

• Disconnect power to the appliance before starting any repair
• Remove the old gasket by loosening door trim or fasteners as needed; clean the sealing surface before installing the new gasket
• Press the new gasket into the channel evenly and ensure the magnetic/locking edge seats fully around the door
• After installation, close the door and check for gaps; allow the gasket to form to the door over normal use

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This lower cover is the front access panel that protects the appliance's internal components and gives the cabinet a finished look. It restores the lower front appearance and shields wiring and assemblies from dust and debris. What it does

• Replaces a cracked, dented, or missing lower front panel to restore protection and appearance
• Covers and protects wiring, hoses, and base components from dust and accidental contact
• Helps reduce drafts and keeps the cabinet interior cleaner
• Common symptom: visible damage, loose panel, or exposed lower components

• Remove power and disconnect the appliance before beginning any work.
• Usually secured with a few screws or clips at the front base; support the panel while removing fasteners to prevent drops.
• Use basic hand tools; avoid forcing clips to prevent cabinet damage.
• If wiring or components are exposed or damaged, inspect and address those issues before reassembly.

A replacement glass refrigerator shelf that provides a sturdy, easy-to-clean surface for storing food and containers. Restores lost storage space and helps keep items organized and visible. What it does:

• Supports food, containers and small appliances inside the refrigerator
• Creates a flat, stable storage surface for better organization
• Helps contain spills on a single surface for easier cleanup
• Restores damaged, cracked or missing shelving to regain full shelving capacity

• One glass shelf

• Handle glass carefully and wear cut-resistant gloves to prevent injury
• Remove food and other items from adjacent shelves before installing
• Slide into existing shelf tracks or clips until fully seated; do not force
• If shelf hardware is damaged or missing, replace mounting clips or supports before use

The Toe Grille Clip is an OEM part for LG refrigerators. This part secures the toe grille to the base of the refrigerator, ensuring it remains in place while providing easy access for cleaning and maintenance. 

Causes of a bad Toe Grille Clip can include breakage due to accidental impacts during cleaning or general wear and tear over time. 

Symptoms of a faulty Toe Grille Clip include:

• The toe grille coming loose or falling off
• Difficulty attaching or detaching the grille for routine maintenance
• Visible damage or deformation of the clip
• Unusual gaps between the grille and the refrigerator base

This OEM LG part is also compatible with some Kenmore models.

This door basket replaces a cracked or worn refrigerator door shelf to restore secure storage for bottles and small items. Durable molded plastic keeps contents organized and prevents spills on the door. What it does:

• Provides a stable shelf on the refrigerator door for bottles, condiments and small containers
• Replaces broken, cracked or loose door bins that allow items to fall or shift
• Restores proper alignment so the door closes without obstruction
• Matches OEM fit and mounting locations for a direct replacement

• Remove all food and items from the door before starting
• Lift out the old basket and snap the new basket into the same door track; no cutting or modification required
• Inspect door seals and surrounding trim during installation; handle edges carefully to avoid injury

This genuine OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's primary functions such as adjusting and maintaining temperature. Over time, a refrigerator's control board can become inoperable due to excessive use. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced.To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and uninstall the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This authentic replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with LG brand refrigerators.

This snap-in hole plug button covers unused panel openings to restore a finished look and help keep out dust and moisture. A simple cosmetic trim piece that snaps into place and blends with the control panel. What it does:

• Covers exposed holes in control panels and consoles to improve appearance
• Helps block dust, lint and small debris from entering appliance openings
• Prevents accidental contact with internal components through unused holes
• Useful when replacing damaged buttons or finishing a repair

• One snap-in hole plug button

• Disconnect power to the appliance before working on the control panel
• Press the plug into the hole until it snaps flush; use a flat tool gently if needed
• Inspect fit and panel edge for damage; replace if cracked or loose to ensure a secure fit
• If panel removal is required, follow manufacturer instructions to avoid breaking clips

This ice bank assembly is the refrigerated bin that stores and helps feed ice from the ice maker to the dispenser, keeping ice contained and ready for use. It restores proper ice collection and flow inside the freezer. What it does:

• Holds and guides ice from the ice maker to the dispenser or access area
• Prevents ice from clogging or falling out of the ice maker area
• Replaces cracked, warped, or damaged ice storage that causes leaks or poor dispensing
• Helps restore normal ice delivery when the ice maker produces ice but it doesn't collect or feed properly

• One ice bank assembly

• Disconnect power to the refrigerator before beginning service
• Work in a dry, well-lit area; remove contents and shelves as needed for access
• Handle edges and the ice bin carefully to avoid damage; wear gloves for grip and protection
• Follow OEM service instructions for removal and reassembly

This replacement control panel cover protects the console area and restores the appliance's finished appearance. It shields buttons and electronics from spills, dust, and everyday wear so controls stay secure and accessible. What it does:

• Protects the control console and underlying electronics from dust, moisture, and impact
• Restores a clean, finished appearance when original cover is cracked, warped, or missing
• Helps keep buttons and switches aligned and functioning properly by securing the front housing
• Reduces risk of debris getting into the control area, which can cause intermittent operation

• Always unplug the appliance or disconnect power before starting work
• Basic hand tools typically required (screwdriver, nut driver); remove console or trim per service instructions
• Handle carefully to avoid scratching the new cover; align clips and fasteners before securing