790-7121-8701 Parts

This top burner gas valve controls and shuts off gas to a single surface burner so you can ignite and adjust flame height safely. Replace a worn valve to restore precise burner control and dependable lighting.

• Regulates gas flow to one surface burner for reliable ignition and flame adjustment
• Acts as the on/off shutoff for that burner via the control knob
• Helps when a burner won't light even though the igniter clicks
• Helps when flame won't adjust smoothly or the knob binds/feels stripped

• Disconnect power and shut off gas supply before servicing
• Remove knob and access the control/manifold area to reach the valve; note tubing and mounting orientation
• Transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections with an approved gas leak-detection solution before restoring service and testing burner operation

This oven door hinge controls and supports the door's movement, allowing it to open smoothly and close tightly. A secure, balanced hinge helps preserve the door seal and maintain consistent cooking temperatures.

• Supports door weight and balances spring tension for smooth opening and controlled closing
• Helps the door close fully against the gasket to reduce heat loss and temperature swings
• Replaces worn or bent hinges that cause sagging, slamming, or a door that won't stay closed
• Can reduce squeaks or binding and restore proper door alignment

• Disconnect power and allow the appliance to cool completely before servicing
• Remove the door; lock hinge clips or insert hinge pins before lifting the door off
• Note hinge orientation and spring tension when transferring; keep hands clear of moving spring arms
• After installation, verify door alignment and that the gasket contacts evenly all around

This is a replacement refrigerant/line connection tube that links the service valve to the regulator line, restoring a sealed pathway for proper cooling system operation. It fits systems using a 3/8" tube connection. What it does:

• Connects the service/stop valve to the regulator/line, maintaining a sealed refrigerant path
• Restores proper flow and pressure routing when the original tube is damaged, cracked, or leaking
• Commonly replaced for visible leaks, hissing at the valve area, or loss of cooling tied to a line break
• Works as a direct, single-piece tubing connector where a 3/8" connection is specified

• One tube to valve connector (3/8" tube)

• Installation requires appliance access and basic refrigeration line handling; tighten fittings to OEM torque specs and verify leak-free with an appropriate leak detector
• Wear safety glasses and gloves; avoid breathing refrigerant vapors and follow manufacturer service documentation

Color: Black.

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This control panel is the exterior trim that houses and protects the oven/range user interface and display, restoring a clean, functional front for the appliance. It keeps buttons and indicators secure and visible for reliable operation. What it does:

• Covers and protects the appliance control buttons, touchpad, and display from spills and damage
• Provides the visible interface for selecting oven functions and viewing status
• Restores a finished appearance to a damaged, cracked, or worn control area
• Helps ensure buttons and indicators align properly for correct operation

• One control panel

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Some models require removing screws or snap clips and gently lifting the old panel from the console
• Handle the panel carefully to avoid scratching the visible finish or bending mounting tabs
• If the panel attaches to electronic components, take care not to damage ribbon cables or connectors; take care not to damage ribbon cables or connectors.

This is a wafer-head screw with a square (Robertson) drive used to secure appliance trim and handle components. It replaces worn or missing fasteners so panels and handles stay firmly attached. What it does

• Secures appliance trim, handles, and lightweight panels where a low-profile wafer head is required
• Square-drive head resists cam-out for reliable tightening
• Common replacement for loose, stripped, or missing fasteners
• Small size fits confined fastening locations without protruding

• One wafer-head square-drive screw (10-24 x 1.6)

• Use the correct square (Robertson) bit to avoid damaging the head
• Tighten securely but avoid over-torquing to prevent thread or component damage
• Disconnect power or follow manufacturer safety guidelines before working near electrical components
• If screw threads are damaged, replace with new threaded insert or correct-size fastener

This water inlet valve controls water flow to the refrigerator dispenser and ice maker, restoring proper dispensing and ice production. It replaces a failed or leaking valve to stop drips and ensure steady water fill. What it does:

• Opens and closes water supply to the dispenser and ice maker when activated
• Stops water flow to prevent leaks when the valve is closed
• Helps restore normal dispenser flow and consistent ice maker fills
• Commonly replaced for leaking, no water dispensed, or weak dispenser flow

• Disconnect power and shut off the water supply before starting any work
• Drain lines and have towels ready; valve replacements can release trapped water
• Basic hand tools required; avoid overtightening fittings to prevent damage

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

This valve mounting screw secures refrigerator water/ice valve assemblies and their mounting brackets, helping keep the valve stable and properly aligned. A simple replacement to address loose or vibrating valve hardware. What it does:

• Secures the valve mounting bracket to the appliance cabinet or valve body
• Fits standard 1/4-20 threaded valve mounting points
• Restores secure mounting when original screw is loose, missing, or stripped
• Helps reduce vibration-related noise and the risk of valve movement that can lead to leaks

• Disconnect power and shut off the water supply before servicing
• Start the screw by hand to avoid cross-threading, then tighten until snug
• Do not over-tighten; replace if threads are stripped or damaged

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit