7907423 Parts

Size: 8-32t x 0.500 inch. Color: Black.

This surface burner cap sits atop the burner head on gas ranges and cooktops, shaping the flame for even heating and shielding the burner from spills. Replace a chipped, warped, or missing cap to restore proper burner performance.

• Shapes and distributes the flame for consistent heat across cookware
• Helps protect the burner head and igniter from drips and debris
• Correct seating supports quick ignition and a clean blue flame
• Common symptoms: uneven or yellow flames, flame lifting, delayed ignition, or constant clicking while lighting

• Allow the burner to cool completely before handling; disconnect power and shut off gas
• Lift off the old cap; clean and dry the burner head surface
• Center the new cap on the burner head so it sits level and does not rock
• Use the cap designated for the correct burner size on your model; re-seat if ignition continues to click or flame is uneven

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Note: ONE screw only, order as needed.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

This fan motor drives your oven's convection fan, circulating hot air for even, reliable cooking performance. Replacing a weak or noisy motor restores proper airflow to reduce hot spots and improve convection baking and roasting results. What it does:

• Powers the rear convection fan to move air across the oven cavity
• Promotes more uniform temperatures on multiple racks during convection cycles
• Helps the oven maintain stable heat during use
• Common symptoms: fan won't spin, intermittent or slow rotation, loud humming/scraping from the rear, uneven results in convection mode

• 1 fan motor

• Disconnect power to the range or wall oven before servicing
• Access may require removing the rear panel or the oven's rear cover; note wire locations for reassembly
• Transfer the original fan blade and mounting hardware to the new motor; handle sharp edges and avoid bending the blade
• Spin the blade by hand to ensure free movement before restoring power

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

The Gas Range Knob is an OEM replacement part for Frigidaire gas ranges and cooktops. It serves as the interface for selecting and adjusting the heat level on gas burners through a simple turn mechanism. 

Symptoms of a bad gas range knob include:

• Difficulty turning the knob or slipping/jumping movements
• Knob appearing loose, cracked or damaged
• Inability to accurately select low heat settings  
• Burner flames not responding as expected to knob position

Causes can be attributed to normal wear over extended use as knobs are rotated frequently during cooking. Exposure to excessive heat or impacts may also degrade plastic knob components.

This OEM Frigidaire replacement is compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This manifold supply tube routes gas from the appliance's inlet/regulator to the burner manifold and valves. Replacing a damaged tube helps restore safe, consistent fuel delivery and reliable burner performance. What it does

• Channels gas from the regulator/inlet to the burner manifold/valve assembly
• Maintains proper fuel flow to multiple burners
• Replace if the tube is bent, cracked, corroded, or leaking
• Symptoms can include multiple burners not lighting or weak/uneven flames due to restricted flow

• 1 manifold supply tube

• Shut off the gas supply and disconnect electrical power before servicing
• Note the routing and orientation of the original tube to match bends and connections
• Use only approved practices for your fitting type; do not apply sealant to flare-seat connections
• After installation, perform a soap-and-water leak test on all joints; do not operate if bubbles appear

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

Replacement water inlet valve that controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and helping stop leaks. Use this valve to address fill and flow issues caused by a failed inlet valve. What it does:

• Opens and closes the water supply to the dispenser and ice maker so they fill correctly.
• Common symptom: no water dispensed or ice maker not filling.
• Common symptom: continuous water flow, visible leaks, or puddling under the refrigerator.
• Typically located where the household water line connects to the refrigerator; valve failures are a frequent source of water-related dispenser and ice problems.

• Disconnect power and shut off the water supply before starting any repair.
• Tighten fittings to the manufacturer's torque recommendations and check all connections for leaks after installation.