79568039218 Parts

Upper hinge assembly that restores proper door pivot and alignment for smooth opening and closing. Replacing a worn or damaged upper hinge helps reduce sag, noise, and uneven sealing so the door closes correctly. What it does:

• Supports and pivots the refrigerator door for stable, controlled movement.
• Keeps the door aligned so the gasket seals evenly and the interior stays cold.
• Use when the door sags, binds, grinds, squeaks, or does not latch evenly.
• Replace bent, worn, or damaged hinge components that cause misalignment.

• Disconnect power and remove items from the door before starting; follow all safety precautions.
• Door removal and reinstallation often require a second person to support the door.
• Hinge orientation and hardware before tightening; follow the manufacturer service instructions for final alignment.
• Reuse or replace mounting screws and bushings as needed; do not overtighten fasteners.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This door gasket assembly seals the refrigerator door to the cabinet, keeping cold air in and humid room air out. Replace a torn or deformed gasket to restore a tight seal, stable temperatures, and reduce frost or condensation.

• Creates an airtight seal around the door perimeter
• Helps maintain proper temperatures and consistent cooling
• Reduces warm-air leaks that lead to frost or condensation
• Common symptoms: torn/warped gasket, visible gaps, door not closing flush, or temperature swings

• Disconnect power before servicing
• Let the new gasket warm to room temperature; use warm water or gentle low heat to relax folds—do not overheat
• Remove the old gasket and press the new gasket fully into the door channel, ensuring corners seat properly
• Close the door and check contact all around; work the gasket as needed until it seals evenly

Door switch magnet for reed switch

This part is a refrigerator control board. This part manages the functions of the refrigerator. This could include cooling the refrigerator and running the defrost times.Since the control board controls the functions of the refrigerator, without it not much will function correctly. If this part has gone bad, the refrigerator will not cool, the lights won't turn on, and the fan won't run. It is important to unplug the refrigerator before attempting to replace the control board. Some people choose to wear work gloves during the replacement process to protect their hands. Be sure to place food in a temperature safe location while replacing this part as the unit will not cool.This specific control board is compatible with refrigerators units that are manufactured by Kenmore and LG. This part is sold individually. It is sourced directly from the manufacturer.

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This cover assembly replaces a damaged or missing cover panel in the designated location of your appliance. It restores proper protection and fit, helping shield components and maintain intended airflow where the original cover has cracked or loosened.

• Protects internal components and wiring from dust, moisture, and accidental contact
• Maintains manufacturer-designed airflow/venting through the cover area
• Restores secure mounting and a clean, finished appearance
• Typical symptoms: cracked or broken cover, missing tabs, loose or rattling panel, or airflow obstruction at the cover location

• Disconnect power to the appliance before servicing
• Remove retaining screws/clips and keep hardware for reuse
• Transfer any clips, seals, or sensors from the original cover if applicable; seat the new cover fully
• Tighten fasteners snugly without overtightening to avoid cracking plastic; ensure vents are unobstructed and the panel is secure

A replacement hinge cap that covers and protects the upper door hinge, restoring a finished look and helping keep the hinge area free of debris. Durable plastic restores appearance and prevents direct wear on the hinge. What it does:

• Covers the exposed upper door hinge to protect it from dirt, dust and moisture.
• Helps prevent cosmetic damage to the door edge by shielding the hinge.
• Replaces cracked, broken or missing caps that leave the hinge exposed.
• Can reduce rubbing or noise caused by a damaged or misaligned cap.

• Typically snaps into place; basic hand tools may be helpful to remove the old cap.
• Support the door or follow manufacturer guidance if hinge removal or adjustment is needed.
• Inspect surrounding hinge components for wear when replacing the cap.

This motor bracket is the OEM-style mounting bracket that secures the appliance motor to the cabinet, keeping the motor aligned and reducing vibration for reliable operation. It helps restore proper motor support and stable running. What it does:

• Provides a secure mounting point to hold the motor in correct position
• Maintains motor alignment to prevent belt slip and uneven wear
• Reduces vibration and noise caused by a loose or damaged motor mount
• Can resolve symptoms such as unusual motor noise, excessive vibration, or motor movement during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance service manual for access steps
• Inspect surrounding components (mounting fasteners, motor and belts) and replace any damaged parts

This handle assembly replaces a broken, loose or worn refrigerator door handle so you can open and close the door safely and restore the appliance's appearance. It fits the factory mounting points for a secure replacement. What it does:

• Replaces damaged or cracked door handle hardware to restore grip and door operation
• Provides a stable mounting point so the door opens and closes without wobble
• Returns the finished look of the appliance when the original handle is scratched or chipped
• Helps prevent injury or food loss caused by a failing or loose handle

• Disconnect power to the appliance or unplug before working on doors to avoid injury
• Most installs require removing the door trim or access panel and fasteners; keep track of screws
• Use a soft cloth to protect the finish during installation and align the handle before tightening