7957313 Parts

This indoor fan motor powers the air conditioner's indoor unit blower to move air across the evaporator coil. Replacing a weak or failed motor restores proper airflow for effective cooling and comfort.

• Drives the indoor blower/crossflow fan to circulate conditioned air
• Maintains correct airflow across the evaporator for cooling and dehumidification
• Common symptoms of failure: no or weak airflow, fan won't start or stalls, intermittent operation
• May cause unusual buzzing/grinding noises or the unit shutting down with a fan-related fault

• Disconnect power at the breaker before servicing; allow moving parts to stop
• Remove the indoor unit cover and access panel; note wire harness connections and routing
• Transfer any brackets, insulators, or hardware from the old motor if required
• Ensure the fan wheel spins freely and does not rub before restoring power and testing

The Bracket Assembly is an OEM part for LG French door refrigerators housing circulation fan motors. This mounting bracket securely attaches the integral evaporator motor within the unit compartment. 

Causes of a bad bracket assembly can include loosened fasteners failing to firmly support vibrations over time, impact dents flexing the steel support reducing balance, or corrosion where steel meets refrigerant lines deteriorating contact points.

Symptoms of a bad bracket assembly include:

• Abnormal noises or grinding sounds from motor  
• Reduced airflow from the inlet to outlets inside the fridge
• Loose parts susceptible to movement damage 
• Misalignment reducing the lifespan of bearings

Replace yours today with this genuine OEM LG bracket to restore optimized cooling performance. Rigid clamping securely isolates motor oscillations. Compatible with Samsung, Kenmore, and GE French door models, this replacement sustains proper fit and function. 

A replacement door gasket assembly that seals the refrigerator door to help maintain internal temperature and reduce energy loss. Restores a proper door seal to help keep food fresher and reduce cooling strain. What it does:

• Forms a tight seal around the refrigerator door to minimize cold-air loss and help maintain set temperatures.
• Helps prevent frost buildup and condensation inside the fresh-food compartment when the seal is compromised.
• Can reduce cycling frequency and excessive run time caused by a damaged or worn door seal.
• Common symptoms of a failing gasket: visible gaps, cold spots, frost or ice buildup, or condensation on the door edges.

• Disconnect power to the appliance before starting any repair.
• Remove food and door-mounted items as needed for safe access and handling.
• Align the gasket into the door channel, working it evenly around the perimeter so it seats fully; some distortion may correct after a short run time.

This connector secures and transmits motion between the drawer drive and the sliding assembly, restoring smooth drawer movement and alignment. It's a direct-fit replacement that helps fix sticking, slipping, or non-moving drawers. What it does:

• Couples the drawer drive mechanism to the sliding gear, allowing the drawer to open and close reliably
• Replaces worn or broken connector teeth or mounts that cause skipping or jammed operation
• Helps correct uneven or noisy drawer movement caused by damaged linkage
• Restores proper engagement so the drawer responds to normal open/close controls

• One connector as shown

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Inspect surrounding gears, tracks, and mounting points; replace any damaged parts for best results
• Basic hand tools are typically required; handle plastic gears carefully to avoid further damage

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This replacement door gasket assembly seals the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal around the door edge for better cooling performance and food preservation. What it does:

• Creates an airtight seal around the refrigerator door to limit cold air escape
• Helps maintain consistent internal temperature for food safety
• Reduces frost buildup and excessive compressor run time when working properly
• Addresses symptoms such as warm spots near the door, visible gaps, or persistent condensation

• One door gasket assembly

• Inspect the door and mounting channel for debris before installing; clean with mild detergent and dry completely
• Gasket typically stretches into a channel and secures around the door perimeter—avoid sharp tools that can damage the seal
• For best results, install at room temperature; warm the gasket gently if needed to ease fitting

This door gasket assembly replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits the door's perimeter and creates the seal between the cabinet and door. What it does:

• Seals the refrigerator door to retain cold air and improve temperature stability.
• Prevents warm air intrusion that can cause frost buildup or increased energy use.
• Helps reduce condensation and water leaks around the door area.
• Restores proper door alignment and closing when old gasket is torn, stretched, or deformed.

• Unplug the appliance and remove food from the door area before starting.
• Work with the door propped or supported; follow OEM removal steps for existing gasket tabs or clips.
• Gently warm and flex the new gasket if needed for easier seating; avoid sharp tools that can puncture it.
• After installation, check the seal around the full perimeter and allow a short run cycle to verify proper operation.

This rear TV cover assembly replaces a damaged or cracked cabinet back to protect internal components and restore the TV's exterior appearance. It provides a secure mounting surface and helps keep ventilation openings intact. What it does:

• Replaces the rear cabinet to protect power and signal boards from dust and impact
• Restores the TV's original fit-and-finish and hides internal wiring and components
• Maintains designed ventilation paths to help prevent overheating when installed correctly
• Common service for cracked, warped, or cosmetically damaged back panels

• One TV rear cover assembly

• Unplug the TV and allow all capacitors to discharge before removing the old cover
• Handle the cover carefully to avoid scratching the finish or damaging alignment tabs
• Retain and reuse original screws and mounting hardware unless replacement parts are specified

This door gasket assembly replaces a worn or damaged refrigerator door seal to restore a tight closure and help maintain proper internal temperature. It fits the specified LG door opening and restores the cabinet-to-door seal. What it does:

• Seals the door perimeter to prevent warm air intrusion and reduce frost build-up.
• Helps maintain consistent internal temperature for food safety and efficient cooling.
• Reduces condensation and moisture that can lead to odor or spoilage.
• Addresses common symptoms like visible tears, gaps, or poor door closure.

• High-level replacement: remove the old gasket, clean the door channel, and press the new gasket into the retainer groove following the OEM pattern.
• Inspect the door frame and retainer for damage before installing; a warped frame can prevent a proper seal.
• Use gentle heat only if needed to ease seating; avoid open flames or excessive heat.
• Disconnect power to the appliance or follow manufacturer safety instructions if removing doors or working near electrical components.

This guide assembly secures and aligns internal TV components to keep the display and front panel stable during use. Replacing a damaged guide restores proper fit and reduces movement or rubbing that can affect the screen or bezel. What it does:

• Positions and supports the TV panel and adjacent internal parts for correct alignment
• Prevents panel flex, rubbing, and audible rattles caused by loose or broken guides
• Helps maintain an even bezel-to-screen gap and proper front-panel fit
• Restores mechanical stability after impacts or wear that crack or deform the original guide

• One guide assembly part as shown

• Disconnect power and fully remove the TV from its mount before starting
• Partial disassembly of the cabinet and removal of the front bezel/panel is typically required
• Handle the LCD/OLED panel carefully to avoid pressure marks or damage during installation
• Use the OEM fasteners and follow service manual orientation; test fit before final reassembly