7957414 Parts

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

The Cover, Lamp is an OEM part for LG dryers. This component covers and protects the interior lamp inside the dryer, ensuring it stays secure and free from damage while providing illumination inside the drum.

Over time, the lamp cover can become cracked or damaged due to the high temperatures and vibrations within the dryer. It is essential to replace a faulty lamp cover to maintain the proper lighting and protection for the lamp.

Symptoms of a bad lamp cover include:

• The interior lamp not staying in place
• Visible cracks or damage on the cover
• Reduced or blocked light inside the dryer drum
• The cover falling off or becoming loose

This OEM LG part is also compatible with Sears/Kenmore models.

This distortion spring applies the correct tension within the dryer mechanism so parts return to position and operate smoothly. Replacing a fatigued or broken spring helps prevent loose movement, rattling, and inconsistent operation of the related assembly. What it does

• Provides the designed return/tension force for the associated dryer mechanism
• Helps maintain alignment and smooth movement of moving parts
• Can reduce rattling or squeaking caused by weak or missing spring tension
• Symptoms include components not returning to position or intermittent operation

• One distortion spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Allow internal components to cool before service
• Control the spring during removal/installation—springs are under tension and can snap back
• Note the original spring orientation and attachment points to ensure proper reassembly

The sheath heater is the electric resistance element that produces heat inside the appliance. Replacing a failed element restores reliable heating so the unit reaches temperature and completes its cook or defrost cycles as designed.

• Generates heat when energized to support baking/broiling or defrost functions
• Helps the appliance reach and maintain target temperature for consistent performance
• Typical failure signs: no or weak heat, long preheat/heat recovery, visible cracks/blisters on the element, or breaker tripping when the element energizes
• In defrost use-cases: heavy frost buildup on the evaporator and poor cooling due to iced coils

• Disconnect power at the breaker or unplug the unit; allow all surfaces to cool completely
• Handle the element carefully—do not bend the sheath; wear cut-resistant gloves
• Note wire positions, transfer any brackets/clips from the old part, and make tight, clean connections
• Inspect nearby high-heat wiring and terminals for damage and replace as needed; test operation before fully closing panels

Right side upper hinge.

This refrigerator door gasket restores a tight seal around the door perimeter. Replacing a worn seal helps keep cold air in, block warm, humid air out, and maintain proper temperatures and efficiency.

• Creates the compression seal between the door and cabinet when closed
• Helps reduce frost, condensation, and temperature swings
• Replaces gaskets that are torn, cracked, warped, or no longer sealing
• Common symptoms: visible gaps, doors not closing fully, moisture around the door, or longer run times

• Disconnect power before servicing
• Warm the gasket in hot water or with a hair dryer on low to relax folds; do not overheat
• Start at the corners and press the gasket lip into the door liner groove, then work along the sides
• Close the door and check for uniform contact around the perimeter; level/adjust hinges if needed

The Door Basket is an OEM part for LG refrigerators. It is used to organize small items and provide additional storage directly on the refrigerator door. 

Symptoms of a bad door basket include:

• Items no longer stay securely in place during opening and closing  
• Sagging or misshapen basket that no longer organizes properly
• Detached basket that no longer mounts firmly on the door

Causes of a bad door basket can include warped or broken plastic, cracks or fractures in the plastic construction, or failure of the mounting brackets over time. 

This OEM LG replacement is also compatible with select Sears/Kenmore models.

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

The Tub Assembly is an OEM component for LG clothes dryers. As the central component housing both the inner and outer drums, the tub assembly is essential for safely drying wet laundry loads. It rotates the drums to circulate air and remove moisture from clothes during cycles. 

Causes of a bad tub assembly dryer can include cracks, leaks, or damage to the drum structure from excessive use or unbalanced loads over time. Wear and tear on rotating or suspension components that impair rotation. 

Symptoms of an issue with the tub assembly dryer are:

• Inefficient or slow drying times 
• Abnormal noises or vibrations during cycles
• Restricted or lack of drum rotation
• Cracks, leaks, or physical damage visible on drums

This OEM LG part is also compatible with Sears/Kenmore.

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

The Damper is an OEM part for LG dryers. This component helps reduce noise and vibrations by damping the movement of the dryer door. It plays an important role in ensuring smooth and controlled opening and closing of the dryer door.

Causes of a bad damper can include wear over time, damage from repeated usage or unbalanced loads, or accidental impact.

Symptoms of a bad damper include:

• Excessive noise or loud banging when opening or closing the dryer door
• The door not opening or closing smoothly
• Increased vibration levels during operation
• Reduced lifespan of other door components like hinges or latches

This OEM LG part is also compatible with some Kenmore models.

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock