970100 Parts

This genuine OEM part is a washer lid. The washer lid is the main piece that covers the washer. Over time, a washer lid can become damaged to the point where it no longer closes securely. If the washer lid is no longer closing all the way or is severely cracked or damaged, it will need to be replaced.To replace this part, start by making sure the washer is unplugged. After it has been powered off, proceed to take a putty knife to lift to release the two retaining clips that secure the washer's main top. Once released, proceed to remove the lid lock assembly wire connector. Fully remove the main top and set it upside down. Release the tension on the lid springs and detach the springs from the main top and hinge bars. Using a Phillips head screwdriver, remove the screws that secure the hinge bars to the lid. Push the hinge bars through the bearings then twist the bars to remove them. This will separate the lid from the main top. Take the new lid and align it with the main top. Insert the hinge bar between the main top and bearing while threading the screws to secure the new top. Reinstall the top panel and connect the wire harness. This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

This is a Frigidaire washer/dryer combo timer. The washer or dryer timer controls all the timed functions of the appliances, including the cycles and draining. Without a working timer, there is no way for the machine to judge when to start certain parts of the cycle, when to drain water, start rinsing, switch from hot to normal air, and many other tasks. When a timer goes out on these machines, a replacement needs to be ordered immediately. To replace this part, first unplug the appliance from the main power source. This timer is a genuine OEM replacement part sourced directly from Frigidaire. This part is only available individually and is not included with other parts or the main appliance. This product is compatible with Frigidaire appliances.

Hex washer head ,10-32 x 0.375. Ground

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This spring clamp secures the refrigerator door bellow to the cabinet, helping hold the bellow in place for a tighter seal and consistent door alignment. A simple replacement that restores proper bellow retention. What it does

• Holds the door bellow tightly to the cabinet or door frame
• Prevents bellow from pulling away or bunching during door use
• Helps maintain a consistent seal to reduce drafts at the door edge
• Works where a worn or damaged clamp allows visible gap or misalignment

• Basic hand tools usually required; inspect surrounding bellow for wear before installing
• Wear gloves and eye protection; spring clamps can snap back during removal/installation
• If clamp is difficult to seat, ensure bellow is properly positioned and not torn
• Replace damaged bellows or additional fasteners to ensure a complete seal

A simple wire-fastening cable tie that secures wiring and small hoses to prevent rubbing, snagging, or loose routing inside the appliance. Helps keep components organized for safer, quieter operation. What it does

• Secures wiring bundles and small hoses to chassis or brackets to prevent abrasion and movement
• Helps stop intermittent shorts or electrical noise caused by wires rubbing or contacting other parts
• Keeps airflow and moving parts clear by holding wiring away from fans and belts
• Useful when replacing or re-routing harnesses during repairs

• Always disconnect power before working on the appliance.
• Loop tie around wiring or hose, pull to secure snugly, and trim excess tail; do not overtighten.
• Replace ties that are brittle or damaged; use the same routing as the original harness.
• Dispose of trimmed ends and avoid sharp edges that could cut wiring insulation.

This replacement control panel restores the appliance's front console and user interface so buttons and the display work reliably. It provides the visible face and mounting surface for controls and status indicators. What it does:

• Houses the appliance's buttons, touchpads, and display area so you can select settings and see status
• Replaces cracked, scratched, or cosmetically damaged panels that affect appearance or button access
• Helps when buttons are unresponsive due to a damaged front panel
• Restores a clean mounting surface for switches and overlays

• Disconnect power before starting any repair to avoid shock or injury
• Remove trim, bezels, or mounting screws as needed to access the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching or cracking; use proper tools to release clips

This upper hinge cover protects and conceals the refrigerator's door hinge assembly for a finished look and safer operation. It helps prevent snags and shields hinge components from dirt and wear while restoring the door's appearance. What it does:

• Covers the upper door hinge to hide hardware and improve aesthetics
• Helps keep dust, grease, and debris off the hinge area
• Reduces the chance of clothing or skin catching on exposed hardware
• Restores a finished, factory appearance when the original cover is cracked or missing

• High-level replacement; some models require removing or loosening the door or hinge fasteners
• Handle carefully to avoid scratching the finish; use the correct screwdriver or fastener tool
• Keep hands clear of the hinge while seating the cover and re-tightening fasteners

A molded gasket that seals the evaporator coil cover to reduce air bypass and help direct cold air over the coils for more consistent cooling. Replaces a worn or damaged seal to help restore proper airflow and reduce frost buildup. What it does:

• Seals the evaporator coil cover to prevent warm air from bypassing the coil
• Helps maintain proper airflow for consistent cooling performance
• Reduces frost or ice buildup caused by air leaks around the coil cover
• Prevents condensation and dripping by keeping air where it belongs

• Disconnect power to the appliance before servicing to avoid electrical shock
• Thaw any frost/ice accumulation and remove the evaporator access cover per manufacturer instructions
• Clean mating surfaces, then press the seal into place ensuring a full, even fit around the cover

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

This evaporator fan cover protects the refrigerator evaporator fan assembly and helps direct airflow for proper cooling. It's a molded replacement part that restores the original airflow path and prevents debris contact with the fan. What it does:

• Shields the evaporator fan and motor from ice buildup and loose debris
• Directs airflow across the evaporator for even cooling in the freezer compartment
• Helps reduce fan noise by stabilizing airflow around the fan housing
• Commonly replaced when cracked, broken mounting tabs are present, or airflow is obstructed

• One fan cover

• Disconnect power before accessing the evaporator compartment to avoid shock and fan injury
• Remove food and evaporator access panels per model service instructions before replacing the cover
• Handle clips and mounting tabs gently—use proper fasteners if any original hardware is damaged
• If you encounter ice buildup on the evaporator, fully defrost and address the underlying cause before reassembly