Dacor Cps230b Serial 3Vd6400703 Parts

This temperature sensor kit replaces a failed refrigerator temperature sensor to restore accurate temperature monitoring and help the control board maintain proper cooling. It's designed for service replacement and OEM fit. What it does:

• Monitors internal compartment temperature so the refrigerator control can regulate cooling cycles.
• Helps prevent overcooling or warming caused by a faulty or open sensor.
• Common symptom fix: refrigerator/freezer running too warm or too cold, or erratic cycling.
• Clears temperature-related error codes when installed in place of a defective sensor.

• Disconnect power to the appliance before starting any repair.
• Handle sensor tip and wiring gently; avoid sharp bends or pinching the harness.
• Route and secure the sensor wiring per OEM locations to ensure correct readings.

This convection element kit replaces the oven's convection heating element to restore even heat for baking and roasting. Use it when the convection system no longer produces consistent hot air or the oven bakes unevenly. What it does:

• Heats air for the oven's convection cooking mode so the fan can circulate consistent temperature.
• Restores even browning and predictable bake/roast results when the convection element has failed.
• Common symptom indicator: uneven baking or roasting, or visible damage to the element.
• Can be part of repairs when the oven does not reach expected results in convection mode.

• Disconnect power at the breaker before starting any repair — electric shock hazard.
• Access typically requires removing the oven cavity back panel or inner rear panel; use proper tools and follow OEM instructions.
• Inspect wiring terminals and insulation; replace connectors that are corroded or damaged.

This thermal cut-off switch is a high-temperature safety device that interrupts power if the appliance overheats. Replacing a failed cutout restores proper overheat protection and can help address no-heat or shutdown issues caused by an open safety circuit.

• Monitors temperature at its mounting location and opens the circuit if temperatures exceed a safe limit
• A failed/open cutout can cause no heat, intermittent heating, or the unit shutting off during use
• Helps protect components from damage due to overheating
• Location varies by model; typically mounted to a bracket or surface near a heat source

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire orientation and transfer leads one at a time to the new switch
• Mount in the original position with firm, flush contact for accurate temperature sensing
• After replacement, inspect airflow/venting and nearby fans/filters to address any underlying overheating causes

This wafer head screw secures panels, brackets, and other components inside your appliance. Replacing worn or missing hardware restores a tight fit, reduces vibration and rattles, and keeps assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or trim with a low-profile wafer head for even clamping
• Replaces stripped, corroded, or missing hardware (#8 x 3/8)
• Helps maintain alignment and reduce vibration or rattling noises
• Restores secure mounting for safe, stable operation

• Disconnect power; also shut off gas before servicing
• Support the panel or component while removing/installing hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Replace screws one at a time to maintain alignment

This wafer-head Phillips screw (#8 x 3/8 in) is a factory fastener used to secure panels, brackets, and covers in compatible appliances. Replace a missing or damaged screw to restore a tight, properly aligned fit. What it does:

• Secures sheet-metal or plastic components to the appliance chassis or subassemblies
• Helps maintain proper alignment and reduce vibration or rattling
• Replaces lost, stripped, or corroded screws of the same size and type
• Used at panel, bracket, and cover mounting points designed for this fastener

• One wafer-head Phillips screw (#8 x 3/8 in)

• Disconnect power (and gas, if applicable) before servicing
• Start threads by hand to avoid cross-threading; use a #2 Phillips driver
• Do not overtighten, especially into plastic or thin sheet metal
• Replace only with the same size/type fastener removed to ensure proper fit

This convection oven motor drives the oven's convection fan to circulate hot air for even cooking. Designed as a direct replacement service motor to restore proper airflow and heating performance in compatible Samsung ovens. What it does:

• Spins the convection fan to circulate hot air for more even baking and roasting
• Helps maintain consistent oven temperature by improving air circulation
• Can address symptoms like uneven cooking, hot spots, or a noisy/non-spinning convection fan
• Matches OEM form and mounting for a straightforward replacement when compatible

• One convection oven service motor

• Disconnect power to the appliance before starting any repair
• Handle with care; verify connector and mounting orientation before final assembly
• Wear gloves and eye protection; avoid contact with sharp sheet metal and heating elements

This broil element heats the top of the oven for broiling and browning, restoring high-heat performance for searing and finishing dishes. Designed to replace a failed or damaged upper heating element. What it does

• Heats from the top of the oven to brown, sear, and broil foods
• Replaces a visibly burnt, broken, or non-heating upper oven element
• Helps fix symptoms such as no broil heat, uneven browning, or visible arcing/sparking
• Works with standard terminal connections used on compatible Samsung ranges

• One broil element (upper oven)

• Disconnect power to the appliance before attempting any service
• Handle element carefully to avoid bending or damaging the tubular element
• Verify terminal connections match your oven and tighten hardware securely

This replacement oven rack restores cooking surface support for convection ovens and lets cookware sit securely for even baking. Designed to match the original oven shelving for proper fit and airflow. What it does:

• Provides a stable shelf for pans, bakeware, and racks inside the oven cavity
• Positions food for improved convection airflow and more even cooking
• Replaces bent, damaged, or missing racks that interfere with sliding or heat distribution

• Install by sliding the rack into the oven's side supports until fully seated; no tools typically required
• Allow the oven to cool and disconnect power before handling or installing to avoid burns or electric shock
• Inspect side supports and rack guides for damage; replace worn guides if the rack does not seat securely
• Clean rack with warm soapy water or a non-abrasive cleaner before first use if needed

This service bushing protects and cushions appliance wiring where it passes through metal panels, helping prevent chafing and shorts. It's a simple replacement that restores proper routing and insulation for harness wires. What it does:

• Cushions wiring at panel openings to reduce abrasion and wear
• Keeps wiring properly routed to prevent pinching or intermittent connections
• Helps stop rattling or vibration where wires contact metal edges
• Addresses symptoms like exposed or frayed insulation, burning smell, or intermittent power related to damaged panel wiring

• One service bushing

• Disconnect power before starting any repair
• Remove the access panel or trim to reach the damaged bushing location
• Press the bushing into the panel hole until fully seated; replace wiring through the bushing as routed originally
• Inspect surrounding wiring and replace any frayed or heat-damaged sections; reassemble panels securely