Swt111wm3069 Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Drain Pump is an OEM part for Speedqueen brand washing machines. Located near the rear of the washer tub, the drain pump works to empty water from the machine at the end of each cycle. It functions through an electrical motor that activates a spinning impeller, forcing water through the drain hose. 

Symptoms of a bad drain pump include:

• Washer fails to fully drain or leaves standing water 
• Drain cycle takes an unusually long time to complete
• Loud grinding or rattling sounds coming from inside

Over time, a buildup of lint or mineral deposits inside the pump chamber can clog the impeller and reduce efficiency. Allowing water to sit for extended periods also promotes mold growth. Replace your drain pump today with this genuine Speedqueen part and restore full draining capability.
 

This water inlet mixing valve controls and blends the hot and cold water entering your washer for proper fill temperature and water level. A worn valve can cause fill problems or unwanted leaks into the tub.

• Regulates hot and cold water flow to achieve the selected temperature
• Opens and closes electrically during fill cycles
• Common symptoms: slow fill, no fill, fills with only hot or only cold, or water seeping into the tub when the washer is off
• Electrical coil-operated design for reliable operation

• Unplug the washer and shut off both water supplies before servicing
• Place a towel or pan to catch residual water when disconnecting hoses
• Note hose positions (hot/cold) and wire connectors for correct reassembly
• After installation, check for leaks and run a test fill cycle

This idler pulley wheel keeps the drive belt aligned and under constant tension so the drive system runs smoothly and quietly. Replacing a worn wheel helps eliminate belt squeal and prevents premature belt wear or slippage.

• Maintains proper belt tension on the idler arm and guides the belt during operation
• Provides low-friction rotation for smooth belt tracking
• Common symptoms of a worn wheel: squealing/squeaking, frayed or glazed belt, belt slipping off, or intermittent/no drive
• Helps restore reliable belt traction and reduce noise

• Disconnect power and wear work gloves before servicing
• Access the drive system and note the belt routing for reassembly
• Release belt tension, remove retaining hardware, swap the wheel on the idler arm, and re-tension the belt
• Spin the new wheel by hand to inspect belt and idler arm/spring and replace if worn

This upper and lower bearing set supports the rotating shaft assembly, helping it turn smoothly and quietly. Replacing worn bearings reduces noise and vibration and protects adjacent components from accelerated wear. What it does:

• Provides radial support so the shaft/drum rotates freely with minimal friction
• Worn bearings can cause rumbling, squealing, or grinding during operation
• Can show play at the shaft or metallic dust near the bearing area

What's included:

• 1 bearing

Install notes:

• Disconnect power and shut off water/gas before servicing
• Access the bearing housing; use a press or proper driver to remove/install bearings—do not strike the races
• Note bearing orientation and seating depth; install squarely and fully
• Inspect the shaft and any related seals/housings and replace if worn or damaged

The Washer Filter is an OEM replacement part for Speed Queen top-loading washing machines. Located at the bottom of the washer tub, this filter traps lint and other debris to prevent plumbing issues. It must be cleaned regularly to maintain optimal water flow.

Symptoms of a clogged or damaged filter include:

• Slow or inadequate water fill levels 
• Cycles taking longer to complete 
• Accumulation of debris in pump/hoses
• Draining or spinning issues

Causes may be related to prolonged use without cleaning, excessive mineral or detergent buildup over time, or physical damage like cracks that allow lint to pass through.

This part is compatible with some Whirlpool, Maytag, and Kenmore-branded top loaders as well.

Dryers, washers, and washer dryer combos are made with an idler pulley shaft. It works in combination with the rest of the equipment in multiple ways. It switches the direction in which the output shaft is rotating. The idler pulley shaft also works to change gears and maintain the space between shafts. With time, because of excessive force, or as a result of misuse, the idler pulley shaft can wear out, break, or get damaged otherwise. When the part isn't working correctly, it has to be replaced to continue using the machine.The primary indication that there is something wrong with the idler pulley shaft is a machine that's producing excessive noises. Replacement of the idler pulley shaft is a straightforward process. It can be done in a few minutes with a nut driver and screwdrivers. Unplug the appliance before starting the disassembly.This idler pulley shaft is a genuine OEM replacement part. It is sold as an individual unit. It is made of durable metal materials. The idler pulley shaft is sourced from the manufacturer. It can be installed in various machines made by Speed Queen, Amana, and Magic Chef.

The Drain Pump is an OEM component for Speed Queen washing machines. It is an important electric part that works to remove water from the washer tub at the end of each cycle. 

Symptoms of a failing drain pump include:

• The washer not fully draining water after cycles
• Excessively long drain times
• Unusual noises coming from the pump area

Causes stem from blockages in the pump chamber or drain hose, worn impeller assembly, or damaged electrical components inhibiting proper operation.

This Speed Queen replacement pump restores the machine's essential draining ability for hygienic washing. It ensures the removal of all water to prevent residual moisture issues. 

A replacement tub cover gasket assembly that seals the washer tub to help prevent leaks and protect internal components. Restores the tub-to-cover seal so your washer can hold water and operate reliably. What it does:

• Forms a watertight seal between the tub cover and tub to reduce dripping or pooling around the cabinet.
• Helps prevent detergent and soil from entering the cabinet or suspension area.
• Addresses symptoms like visible leaks at the top of the tub, water on the floor near the washer, or a damaged/torn seal.
• Replaces worn or cracked gasket material that can fail over time.

• One tub cover gasket assembly (cover with gasket)

• Disconnect power and turn off the water supply before starting any repair.
• Basic hand tools are typically required; the cover may need to be removed to access the gasket seating area.
• Inspect surrounding clips, fasteners, and sealing surfaces for damage and replace as needed for a complete seal.

This switch knob fits onto the control switch shaft so you can select settings and operate the machine. Replacing a cracked, stripped, or missing knob restores smooth, reliable control and keeps daily use straightforward. What it does:

• Fits over the control switch shaft to turn the switch and choose settings
• Restores a secure grip and clear position when selecting options
• Helps resolve issues like slipping when turning or a knob that won't stay attached
• Common symptoms: cracked knob, stripped insert, loose or missing knob, difficulty selecting settings

• 1 switch knob

• Disconnect power before servicing
• Pull the old knob straight off; remove any retaining clip or set screw if present and save it
• Align the flat/D-shaft orientation and press the new knob fully onto the switch shaft
• Test the switch through all positions to confirm proper engagement

This small sealing washer fits the washer's water pressure assembly to help maintain a proper watertight seal at the pressure/valve connection. Replacing a worn washer reduces leaks and helps the fill/pressure system operate as intended. What it does

• Provides a watertight seal at the water pressure/valve connection to prevent leaks.
• Helps maintain correct pressure feedback to the washer's water control system.
• Wear or damage can allow leaking at the valve or inconsistent fill behavior.
• Simple, low-cost part commonly replaced when troubleshooting valve leaks.

• Turn off household water supply and unplug the washer before replacing.
• Remove the valve/pressure fitting carefully and replace the old washer with the new one, making sure it seats flat and undamaged.
• Inspect mating surfaces for debris or damage; clean before reassembly.
• If leaks or fill issues persist after replacement, inspect related seals, fittings, and the pressure switch/valve assembly.

This mixing valve assembly controls and blends hot and cold water to deliver the correct wash temperature for the machine, restoring proper fill temperature and cycle performance. What it does

• Regulates and mixes incoming hot and cold water to achieve set wash temperatures.
• Helps prevent excessively hot or cold fills and temperature-related wash issues.
• Common fix for cycles that fill with only hot or only cold water or inconsistent water temperature.
• Operates on 120V electrical supply when applicable to the model.

• Disconnect power and shut off both hot and cold water supplies before starting.
• Verify valve orientation and inlet/outlet connections match the machine; replace mounting hardware as needed.
• Inspect hoses and fittings for leaks after installation and run a test cycle to confirm proper temperature control.

This is a 1/4-15 x 3/4 hex head screw used to secure components in laundry appliances. It provides a strong, threaded fastening point for panels and brackets so parts stay properly aligned during operation. What it does:

• Fastens panels, brackets, or components where a 1/4-15 x 3/4 hex head screw is specified
• Holds assemblies securely to reduce vibration and movement
• Can be used to replace a worn, stripped, or missing screw to restore proper fit
• Matches OEM thread and length for correct engagement when used as specified

• One 1/4-15 x 3/4 hex head screw

• Disconnect power to the appliance before performing any repairs
• Use the correct hex driver/socket to avoid rounding the head
• Tighten snugly but avoid over-torquing to prevent stripping threads or cracking components
• Replace with the exact part if damaged;

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This is a 1/4-20 x 9/16 hex flange screw used to secure panels and assemblies on commercial and residential laundry equipment. It provides a durable, threaded fastener that restores proper fit and prevents rattling or loose components. What it does:

• Fastens panels, brackets, and components where a 1/4-20 hex flange screw is specified
• Replaces stripped, corroded, or missing screws that cause loose parts or vibration
• Restores secure connections that can reduce noise and align panels
• Used in areas requiring a flange head for wider bearing surface and resistance to loosening

• One 1/4-20 x 9/16 hex flange screw

• Install with the correct size hex driver or socket; avoid over-tightening to prevent stripping
• Replace any damaged or corroded mating hardware as needed for secure fit
• Disconnect power and follow safety procedures if working near electrical components