Bosch Shxm63ws5n Parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This regeneration valve directs brine through your dishwasher's built-in water softener during recharge cycles, helping prevent hard-water film and spotting. Replacing a faulty valve restores consistent softening and better cleaning results.

• Opens to route salt brine through the ion-exchange resin during regeneration
• Helps maintain proper water hardness feeding the wash system
• Failure can lead to white film/spots, cloudy glassware, mineral buildup, and reduced cleaning
• Also contributes to inconsistent softener performance over time

• Disconnect power and turn off the water supply before servicing
• Access location varies by model; note hose routing and valve orientation during removal
• Inspect hoses and seals; replace if worn to prevent leaks
• Restore water/power and run a short cycle to check for leaks and proper operation

This overflow component directs excess water safely back into the dishwasher's water path to help prevent overfilling and leaks. Replace if damaged to restore correct water management and leak protection.

• Guides overflow water away from the tub into the proper return/drain path
• Helps maintain correct water level during fill
• Can address water collecting in the base pan or leaking from the lower front area
• Useful when the leak protection/float has been tripped or cycles stop due to a detected leak

• Disconnect power and turn off the water supply before servicing
• Access the overflow/water-channel area per your model's service procedure
• Note orientation and transfer any clips or seals from the old part if present
• Reassemble, restore power/water, and run a short cycle to check for leaks

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This cable harness routes power and signals between appliance control and components to restore reliable electrical connections. It replaces a damaged or worn harness to help eliminate intermittent operation and connectivity issues. What it does:

• Replaces the main wiring harness that links controls, sensors, and motors for proper electrical communication
• Restores reliable power and signal paths to correct intermittent power, non-responsive controls, or components that won't run
• Ensures secure connector mating to prevent arcing and poor contact
• Matches OEM connector types and wire lengths to fit in the original routing

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare the new harness to the old one for connector types and routing before installation
• Handle connectors by the housings; do not pull on wires. Ensure all plugs snap fully into place

This insulating part is a replacement insulation panel that helps protect oven components and reduce heat transfer. Restores proper thermal protection to maintain safe operation and protect nearby parts from excess heat. What it does:

• Provides thermal insulation between heating elements and surrounding cabinet components
• Protects wiring, electronics, and panels from heat exposure
• Helps reduce heat transfer that can cause overheating or premature wear of nearby parts
• Visible signs it's needed: damaged, compressed, scorched, or missing insulation

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Handle carefully; insulation may be fragile or dusty—wear gloves and a mask if needed
• May require removal of access panels or adjacent components for replacement

This program control module is the dishwasher's main electronic control board that manages cycle selection and timing, so your appliance can run intended wash programs and respond to user commands. What it does

• Controls wash cycles, timers and user interface commands to start, pause or cancel cycles
• Sends signals to pumps, valves and heaters so the dishwasher advances through its programmed steps
• Helps the unit display error messages or fault codes when a component reports a problem
• Replaces a failed control board when the dishwasher won't start, won't complete cycles, or shows unresponsive controls

• Disconnect power at the breaker or unplug the appliance before service to avoid electric shock
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available
• Expect to remove the control panel and mounting screws; keep track of connector positions for reassembly

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

The Dishwasher Handle End Cap is an OEM part for Bosch dishwashers. This part provides a finishing touch to the dishwasher's door handle, covering the ends for a smooth, finished appearance. Over time, these end caps can become lost, damaged, or worn, affecting the overall look and use of the dishwasher.

Symptoms of a bad Dishwasher Handle End Cap include:

• Missing or loose end caps
• Visible damage or wear 
• Diffiuculty opening the door

Causes of a bad handle end cap can range from accidental damage during cleaning or use, to natural wear and tear from repeated handling. 

This OEM Bosch part can also be used on Thermador and Gaggenau appliances.

The Spray Arm Water Supply Tube is an OEM replacement part for Bosch dishwashers. This tube is responsible for directing water from the dishwasher’s pump to the spray arms, ensuring that dishes are thoroughly cleaned during the wash cycle. Per Bosch this part includes 10027073.

Over time, the spray arm water supply tube can become clogged with debris, develop cracks, or suffer from wear and tear due to regular use. Issues such as mineral buildup, damage from loading and unloading dishes, or general deterioration can affect its performance.

Symptoms of a bad spray arm water supply tube include:

• Poor cleaning performance with food particles left on dishes
• Low water pressure at the spray arms
• Leaks inside the dishwasher
• Unusual noises during the wash cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Handle is an OEM part for Bosch dishwashers. It provides the surface for securely grasping and maneuvering the dishwasher door during opening and closing. 

Causes of a bad handle can include wear and tear from ongoing grasping motions. Repeated lifting and adjusting of the door places stress on handle components over time.

Symptoms of a bad handle include:

• Looseness, wobbling or detachment from the door assembly
• Sharp edges, cracks or splits compromising a firm grip
• Reduced ability to precisely guide the door into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Thread Bolt is an OEM part for Bosch dishwashers. It serves as a fastening component, securing the water inlet in place and ensuring a proper water supply connection.

Causes of a malfunctioning Thread Bolt can include cross-threading or over-tightening during installation, leading to stripping or damage.  

Symptoms of a bad Thread Bolt include:

• Leaks around the water inlet area Loose or rattling water inlet valve 
• Difficulty in accessing or removing the valve assembly 

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.