Bosch Was20160uc/28 Parts

This replacement fixture assembly secures internal components and restores proper alignment and fit in compatible appliances. Replacing a worn or damaged fixture helps stop noise, prevent rubbing, and maintain safe operation. What it does:

• Holds adjacent parts in the correct position to prevent movement and misalignment
• Reduces rattling, vibration, or scraping noises caused by loose or broken supports
• Helps maintain door/panel fit and seals where applicable
• Restores the original mounting function to prevent further wear on connected components

• Disconnect power and water before beginning any repair
• Use basic hand tools; follow service manual or tech sheet for exact disassembly steps
• Handle carefully to avoid damaging surrounding trim, wiring, or seals

This outer housing cover protects internal components and finishes the appliance exterior, helping keep dirt and moisture out while maintaining a clean, safe appearance. Fits original equipment to restore proper enclosure. What it does:

• Shields internal wiring, controls, and mechanisms from debris and accidental contact
• Helps prevent moisture and grime from reaching sensitive parts
• Restores the appliance's exterior appearance when the original cover is cracked or missing
• Can reduce drafts or minor vibration paths when installed correctly

• One outer housing cover

• Disconnect power (and water, if applicable) before beginning any repair
• Use appropriate hand tools; retain all fasteners for reassembly
• Inspect adjoining seals and mounting points; replace damaged hardware as needed

This upper dispenser tray replaces a cracked or worn tray in the dishwasher dispenser assembly to help contain detergent and direct water flow for reliable dispensing. It restores the dispenser area's fit and function. What it does:

• Replaces the upper tray that sits above the detergent/dispenser opening
• Helps channel water and detergent for proper dispensing during the wash cycle
• Prevents leaks and reduces buildup caused by a damaged or warped tray
• Common symptom: visible cracks, warping, or detergent pooling around the dispenser area

• Remove power to the appliance before attempting service
• Typically accessible from the dishwasher door or dispenser assembly; follow OEM disassembly steps
• Handle parts carefully to avoid damaging tabs or clips that secure the tray

This lower dispenser tray fits inside the dishwasher detergent dispenser and provides a stable catch and guide for detergent and rinse aid, helping the dispenser operate cleanly and reliably. Replaces a cracked or warped tray to reduce leaks and residue buildup. What it does:

• Holds and positions the lower portion of the detergent/dispenser assembly for proper door sealing and release
• Directs detergent and rinse aid into the wash chamber when the dispenser opens
• Helps prevent leaks and pooling that can cause poor detergent release or residue
• Restores proper alignment if the original tray is cracked, broken, or deformed

• Disconnect power to the appliance before starting any repair
• Remove the dishwasher door inner panel or dispenser bezel as required to access the dispenser assembly
• Handle parts gently to avoid damaging clips and seals; replace any worn gaskets

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten

This glass front panel replaces a cracked or damaged outer door surface to restore appearance and protect internal components. It provides the visible exterior surface for the appliance door and keeps the interior sealed from everyday wear. What it does:

• Replaces broken, cracked, or scratched outer door glass to restore the appliance's exterior
• Protects controls and internal layers behind the door from impact and debris
• Restores a smooth, easy-to-clean surface and original appearance
• Helps prevent sharp edges or glass fragments from exposing internal parts

• Handle carefully; wear cut-resistant gloves and eye protection to avoid injury from sharp edges
• Remove power to the appliance before starting any disassembly
• Follow OEM disassembly instructions for removing the door assembly and separating layers—do not force components
• If adhesive or clips are used, replace any damaged fasteners and allow adhesives to cure per manufacturer guidance

This analogue pressure sensor detects water pressure to help the appliance monitor and control water level during cycles, reducing overfill and poor wash performance. It replaces a failed or intermittent pressure-sensing assembly. What it does:

• Senses water/air pressure changes and sends an analogue signal to the control board
• Helps the appliance detect correct water level for fill and drain operations
• Commonly used when the appliance shows water level errors, won't fill properly, or cycles erratically
• Can resolve intermittent or no-signal conditions caused by a faulty sensor

• One analogue pressure sensor

• Disconnect power (and water, if applicable) before inspection or replacement
• Handle the sensor and its connector carefully to avoid damage to terminals or diaphragm
• Verify hose and fittings to the sensor are clean and free of kinks or blockages

This fixing kit supplies the mounting and fastening hardware used to secure appliance components during installation or repair, helping restore proper fit and reduce vibration or loose panels. Ideal for replacing missing or damaged fasteners. What it does

• Provides the specific screws, clips, and brackets used to anchor panels or assemblies
• Stops rattling and vibration caused by loose or missing mounting hardware
• Restores proper alignment of doors, panels, or internal components
• Replaces worn or corroded fasteners that can compromise a secure fit

• Disconnect power and water before beginning any repair work
• Use proper tools and follow the appliance manufacturer's installation instructions
• Inspect surrounding components and mounting surfaces; replace any damaged parts

This replacement dispenser tray fits the detergent cup assembly to hold and release dishwasher detergent for normal wash cycles. Restores proper detergent containment and helps ensure detergent is delivered during the wash. What it does

• Holds powdered or tablet detergent in the machine's dispenser area
• Allows detergent to be released at the correct time during the wash cycle
• Replaces cracked, warped, or missing trays that cause leaking or improper release
• Helps prevent detergent from dissolving too early or pooling inside the dispenser

• One dispenser tray

• Disconnect power (and water, if applicable) before servicing for safety
• Remove the old dispenser by opening the door and releasing the dispenser latch; install the new tray by aligning and snapping into place
• Check the dispenser cover and latch operation after installation to ensure proper release

This flexible inlet/fill hose routes water into the appliance, restoring proper water delivery for normal operation. Replace a damaged hose to stop leaks and ensure reliable water flow. What it does:

• Carries incoming water from the supply to the appliance fill assembly
• Prevents water leaks when intact; a cracked or split hose can cause pooling or drips
• Restores normal fill behavior when worn or collapsed hoses reduce flow
• Works with clamps or fittings at each end to create a watertight seal

• One flexible inlet/fill hose

• Turn off the water supply and disconnect power before removing the old hose
• Inspect and replace any worn clamps, gaskets, or fittings for a secure seal
• Hand-start fittings, then tighten with tools—avoid over-tightening to prevent damage
• After installation, restore water and power, then run a short cycle and check for leaks