Bosch Wfmc5301uc/13 Parts

This door hinge secures and lets the refrigerator door pivot for smooth opening and reliable closing. Replacing a worn or damaged hinge helps restore proper door alignment and prevents rubbing, sagging, or uneven gaps. What it does:

• Holds the door to the cabinet and provides the pivot point for opening and closing.
• Restores correct door alignment to stop scraping, binding, or uneven sealing.
• Helps eliminate door sag that can cause gaps or improper closing.
• Matches the OEM fit and mounting points when replacing a failed hinge.

• Disconnect power to the appliance and remove food and shelves from the door before starting.
• Support the door while removing the old hinge to prevent dropping or damage.
• Reuse or replace mounting hardware as needed; tighten fasteners securely and check alignment after installation.

This replacement screw secures appliance panels, brackets, and internal components so your unit stays assembled, aligned, and quiet. Replace stripped, missing, or corroded screws to restore a tight fit and help prevent vibration or leaks.

• Fastens panels, trim, brackets, or internal parts in their correct position
• Helps maintain alignment and sealing to reduce noise and potential leaks
• Replaces worn, stripped, rusted, or lost hardware
• Common symptoms: loose or rattling panel/handle, misaligned parts, components shifting

• Disconnect power and, if applicable, shut off water before servicing
• Match the head/size to the original hardware; do not mix lengths across locations
• Start threads by hand to avoid cross-threading; tighten snugly without over-torque
• For plastic or thin sheet metal, avoid overtightening to prevent stripping or cracking

Outer door panel that restores the appliance's exterior and protects internal door components. Replaces dented, scratched, or corroded fronts to improve appearance and help the door close and seal correctly. What it does:

• Replaces the damaged outer face of the door—symptoms include visible dents, deep scratches, or peeling finish.
• Covers and protects internal door components from dirt and moisture—symptoms include rust at the door edge or moisture inside the door cavity.
• Restores consistent door alignment and feel—symptoms include uneven gaps, a door that doesn't sit flush, or difficulty latching.

• Disconnect power to the appliance before beginning any work.
• Use care when handling sheet metal to avoid cuts; wear gloves and eye protection.
• Door removal is often required; retain and reuse original fasteners and gaskets unless damaged.

The Analogue Pressure Switch is an OEM part for Bosch washing machines. It is part of the water fill system, used to monitor water pressures during inlet filling. The switch communicates pressure levels to the control module.

Causes can be worn contacts, mineral deposits obstructing function, or moisture damage over time.

Symptoms of a bad analogue pressure switch include:

• Inconsistent or inadequate water levels during fill cycles
• Error codes or faults related to water pressure readings
• The washer failing to fill or dispense water as needed

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

A small replacement screw used to secure panels, brackets, and other appliance components. Restores proper fastening to reduce rattling and prevent parts from becoming loose or detached during operation. What it does:

• Fastens panels, trim, brackets or assemblies in place to maintain structural fit
• Replaces missing, stripped, or corroded screws that cause rattling or loose parts
• Helps restore normal operation by keeping components aligned and secure
• Works wherever the OEM screw specification and thread fit this mounting point

• Disconnect power (and water, if applicable) before servicing the appliance
• Use the correct screwdriver and size to avoid stripping the head
• Tighten snugly but avoid overtightening, which can strip threads or crack plastic
• Verify threads and length match the original part before final installation

This hose inlet connects the household water line to the appliance's fill system, restoring proper water delivery for normal cycles. It's a direct replacement for damaged, cracked, or leaking inlet hose assemblies. What it does

• Channels incoming water from the supply into the appliance's fill system.
• Prevents leaks at the supply connection when intact and properly installed.
• Commonly replaces hoses that are cracked, split, or worn and causing visible leaks.
• Can resolve issues with poor or no water fill when the hose is blocked or damaged.

• Disconnect power and shut off the water supply before starting.
• Inspect and replace any worn O-rings, ferrules, or clamps as needed.
• Hand-tighten fittings, then secure with recommended clamps; avoid overtightening.

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

Includes(1)Shipping Bolt,(1)washer,(1)sleeve

The Shipping Bolt is an OEM part for Bosch washing machines. This bolt is designed to secure the washer drum assembly during shipping to prevent excessive movement and potential damage.

Causes of a bad shipping bolt can include stripping, damage to the threads, or loss of the bolt entirely during shipment or installation.

Symptoms of a damaged or missing shipping bolt include:

• Excessive shaking or rattling noises from inside the washer drum
• The drum not rotating properly during wash cycles
• Reduced washing efficiency and improper washing performance

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

2 included - Front load

This hose inlet is the dishwasher water-connection fitting that routes incoming water into the appliance. It provides a secure connection to help prevent leaks and ensure consistent water supply for normal wash cycles. What it does:

• Connects the household water supply to the dishwasher's internal water system
• Seals the inlet to help prevent drips or leaks at the connection point
• Ensures the appliance receives steady water flow for proper filling and operation
• Be replaced when the inlet is cracked, corroded, or leaking

• Disconnect power and shut off the water supply before starting any work
• Inspect and replace any worn O-rings or gaskets when installing the new inlet
• Hand-tighten fittings and then check for leaks; retorque per OEM guidance if available