Cye22tshhgss Parts

This refrigerator drain tube and valve assembly channels defrost water to the drain pan, while the valve helps block warm air from entering the drain. Replace a cracked or clogged assembly to address leaks and recurring ice buildup. What it does:

• Routes defrost water from the evaporator to the drain pan beneath the unit
• Integrated valve helps prevent warm air backflow that can lead to frost and drain clogs
• A damaged or obstructed tube/valve may cause water inside the compartments or on the floor
• Visual cracks, deformation, or blockage indicate the assembly should be replaced

• One drain tube and valve assembly

• Disconnect power and wear cut-resistant gloves before servicing
• Pull the refrigerator forward and remove the rear lower access panel
• Locate the drain outlet above the drain pan; remove the old tube/valve and clear any debris from the drain
• Seat the new assembly fully and ensure proper routing into the drain pan before restoring power

The Meat Pan Slide is an OEM part for GE refrigerators. It is located on the upper shelf and allows for pulling out a multi-purpose pan ideal for storing large food items. 

Causes of a bad Meat Pan Slide can include damage or deformity from exposure to heavy loads over time, broken or cracked plastic parts from repeated pull-out/push-in movement, or obstruction from built-up ice or debris inside the rails.

Symptoms of a bad Meat Pan Slide include:

• The slide becomes stuck and failing to extend or retract
• Gaps appearing between the slide and rails allowing for food items to fall 
• Cracked or broken parts that cause instability or inability to properly support food pans

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Refrigerator Evaporator with Heater is an OEM part for GE refrigerators. This component cools the air within the freezer and fresh food compartments through vaporization and circulation. It also contains an internal heater to prevent condensation and frost formation.

Causes of a bad evaporator can include normal wear over time, damage from leaks, or issues with the heater component. 

Symptoms of a bad evaporator include:

• Inadequate or inconsistent cooling within compartments  
• Frost or condensation buildup that requires frequent defrosting
• High energy usage but inability to maintain proper temperatures
• Foreign or musty odors emanating from within the refrigerator

Replace this evaporator to restore optimal cooling performance, efficiency, and freshness preservation in your refrigerator. This GE OEM part is also compatible with later Hotpoint, RCA, and select Kenmore refrigerator models.
 

The Quick Space Shelf is an OEM component for GE side-by-side refrigerators. With adjustable sliding shelves on silver tracks, it provides flexible small-item organization and storage optimization. Convenient access relies on functional shelving. 

Symptoms of a faulty quick space shelf include:  

• Shelves sticking or jamming during movement along tracks
• Difficulty retracting or extending shelves fully  
• Warped or cracked plastic interfering with balanced item placement

Causes involve repetitive overloading weakening mounting rails, moisture exposure distorting shelf material integrity, or wearing of track rollers inhibiting smooth sliding over extended use.

Replacing with this genuine GE shelf ensures dependable quick access storage through resiliently engineered shelving. Compatible for Hotpoint, RCA, or Kenmore units seeking small area preservation and convenient retrieval of condiments or snacks.

The Freezer Lower Slide is an OEM replacement part for GE refrigerators. It is designed to provide smooth and easy movement of the freezer drawer, allowing for convenient access to your frozen goods.

A bad freezer lower slide can occur due to factors such as wear and tear, damage, or misalignment. If you notice symptoms such as difficulty in sliding the freezer drawer, a loose or broken slide, or an unstable freezer compartment, it may indicate a faulty or malfunctioning left freezer lower slide.

Symptoms of a bad freezer lower slide include:

• Difficulty in sliding the freezer drawer
• Loose or broken slide
• Unstable freezer compartment

Restore your refrigerator's freezer drawer by replacing the faulty left freezer lower slide with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This spring feeler arm is the replacement sensing arm used with the refrigerator ice maker assembly to detect ice level and help actuate the ice-making mechanism. Restores proper ice sensing and helps prevent overfill or stoppage. What it does:

• Acts as the ice maker's feeler/bail arm to detect when the ice bin is full or empty.
• Triggers the ice maker to stop or continue cycles based on ice level.
• Helps prevent overfilling and reduces ice production problems caused by a bent or broken arm.
• Can stop erratic ice maker behavior when the original arm is damaged or worn.

• Disconnect power to the refrigerator before beginning any repair.
• Handle the arm carefully and inspect the ice maker mounting points for damage before installation.
• Reuse factory hardware if undamaged; replace any stripped or missing fasteners.

This bar reinforcement is a replacement support brace that restores strength and alignment to the appliance trim or door assembly. It helps secure panels and prevents sagging or flexing for reliable everyday use. What it does:

• Provides structural support for the door or trim assembly to reduce flex and maintain alignment
• Restores a loose or sagging panel to proper position
• Helps keep connected components stable during normal operation
• Designed to fit into the original mounting points and distribute load where the factory part did

• Follow the appliance manufacturer's service manual for disassembly and reassembly steps
• Use appropriate hand tools; avoid overtightening fasteners to prevent damage
• Disconnect power (or gas, if applicable) and remove food/contents from working area before starting

This evaporator block seal is a refrigerator freezer gasket that helps seal the evaporator assembly to limit air and moisture migration, reducing frost buildup and helping the cooling system run efficiently. What it does:

• Seals the evaporator block area to prevent moist air from reaching cold surfaces
• Helps reduce frost and ice accumulation on the evaporator and evaporator cover
• Supports consistent cooling by maintaining the intended airflow path
• Can reduce defrost frequency when the original seal is damaged or worn

• 1 evaporator block seal

• Disconnect power to the appliance before starting any repair
• Replacement typically requires removing the evaporator cover or assembly; handle evaporator fins and components carefully
• Inspect surrounding foam, clips, or adhesive; replace or resecure as needed to ensure a proper seal
• After installation, restore power and verify proper cooling and defrost operation

This left-side hinge top pin assembly secures the refrigerator door to the cabinet hinge, restoring proper alignment and smoother door movement. Use it to replace a worn or damaged top hinge pin for improved closing and reduced door sag. What it does:

• Secures the door at the cabinet top and provides the pivot point for opening and closing
• Replaces worn or bent pins that can cause door sag, misalignment, or rubbing
• Helps the door close more evenly and maintain a consistent seal
• Works with the existing hinge components to restore smooth hinge action

• Disconnect power to the appliance and remove stored items from the door before starting
• Support the door while removing and installing hinge parts to prevent dropping or damage
• Basic hand tools are typically required; follow the appliance manufacturer's service instructions
• Replace all affected components for a secure fit

This evaporator cover houses and protects the freezer evaporator coil while directing airflow for even cooling and helping limit frost buildup. It restores proper airflow routing behind the freezer liner for consistent temperature control. What it does:

• Protects the evaporator coil from contact and debris
• Guides cold air from the evaporator into the freezer compartment
• Helps reduce localized frost accumulation on the coil and liner
• Can address symptoms like poor/freezer cooling, uneven temperatures, or increased frost/icing

• One evaporator cover (housing) as shown

• Disconnect power before beginning any repair
• Remove interior panels and shelves per your model's service instructions to access the evaporator area
• Handle carefully to avoid damaging the cover tabs, mounting points, or nearby wiring/insulation
• After installation, reassemble panels and verify proper fan operation and normal cooling

This selector control provides the hi/lo switching function for the oven/range heating circuit, restoring user control over high and low heat settings. It replaces a failed selector so the range can select the proper heat level reliably. What it does:

• Switches between high and low heat settings for the heating element or burner
• Restores control when heat setting changes do not respond or stick
• Helps eliminate intermittent or no-heat conditions caused by a worn selector
• Matches OEM function and mounting for a direct replacement

• One selector control assembly as shown

• Disconnect power to the appliance before starting any repair
• Handle electrical connections carefully; note wire locations or take a photo before removal
• Use basic hand tools; do not force connectors or mounting tabs

This upper divider basket replaces the removable compartment divider used to separate items in the appliance's storage basket, helping keep contents organized and accessible. It restores the intended layout and containment for smaller items. What it does:

• Separates and organizes items inside the upper basket to prevent shifting and mixing
• Restores proper fit and containment when the original divider is cracked, broken, or missing
• Helps maintain airflow and access to stored items by keeping compartments tidy
• Visible, molded replacement that matches the original mounting points and profile

• One upper divider basket

• Empty the basket and remove any shelves or trays needed to access the divider before installing
• Inspect mounting tabs or slots for damage and align the part with the original attachment points for a secure fit
• Use care to avoid forcing clips; damaged clips may require replacement of the mounting hardware

This replacement filter cover houses the filter's RFID tag and secures the cartridge in the refrigerator's filter compartment, restoring proper seating and allowing the dispenser/monitoring system to detect the filter. What it does:

• Protects and secures the water filter cartridge in the filter housing
• Houses the RFID/tag sensor so the appliance can recognize the installed filter
• Helps ensure a proper seal and correct filter seating
• Commonly replaced when the cover is cracked, broken, missing, or the filter won't stay in place
• Resolves filter-detection or filter-status errors when the cover or RFID is damaged

• Remove the filter cartridge before replacing the cover; follow the refrigerator owner's manual for proper removal
• Inspect the filter and housing for damage or debris before installing the new cover
• Align and snap the cover into place until it seats securely; the filter status light resets per the appliance instructions