Dacor Er-36D-C-5Ch Parts

This replacement service wire harness routes 110 VAC power to oven or laundry appliance components so they can operate safely and reliably. It restores proper electrical connections when the original harness is damaged or worn. What it does:

• Replaces a damaged or burnt 110 VAC wiring harness to restore power to affected components
• Helps stop intermittent power loss, component failures, or operation issues caused by broken wires or connectors
• Provides factory-style connector ends and wiring configuration for a direct-fit repair when compatible
• Prevents arcing and short circuits from frayed wiring when installed correctly

• Always disconnect power at the breaker or unplug the appliance before beginning service
• Route the harness following the original wiring path and secure with clips or ties to avoid pinching
• Inspect connectors for corrosion and ensure secure, fully seated connections before restoring power

This re-ignition module controls spark for gas surface burners and automatically re-sparks if the flame goes out, helping burners ignite consistently and stay lit when the original module has failed. What it does:

• Sends high-voltage pulses to the burner igniters to light gas
• Provides re-ignition if a burner flame is extinguished
• Distributes spark output to multiple burners as designed
• Common failure symptoms: no spark on all or most burners, continuous clicking, or intermittent ignition across burners

• 1 re-ignition module

• Disconnect electrical power at the breaker and shut off gas supply before servicing
• Access location varies by model; remove rear cover or top as required
• Label and transfer each wire one at a time; mount the module securely and route wires away from heat
• After installation, test each burner for proper ignition and that clicking stops once flame is established

This dual burner gasket seals the burner assembly to the cooktop surface. Replacing a worn or missing seal helps contain spills, maintain proper airflow for a steady flame, and protect the cooktop from heat and moisture intrusion.

• Creates a tight seal between the dual burner base and the cooktop
• Helps maintain proper air/gas flow for consistent ignition and flame quality
• Helps keep spills and debris out of internal burner compartments
• Replace if the seal is cracked, flattened, brittle, or missing; or if flames lift or yellow around the burner

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the appliance to cool completely before disassembly
• Remove grate, burner cap, and burner head to access the seal; clean mating surfaces before installing
• Seat the gasket flat without stretching; reassemble and verify proper burner operation per manufacturer instructions

The Halogen Light Assembly is an OEM part for Samsung ovens. It provides illumination within the oven cavity, allowing you to easily monitor the cooking progress of your dishes.

A bad halogen light assembly can be caused by electrical issues, component failure, or damage to the bulb or socket. When the light assembly malfunctions, it can result in a range of problems, such as no light being emitted, flickering light, or the bulb not turning on at all.

Symptoms of a bad halogen light assembly include:

• No light emitted from the oven cavity
• Flickering light or poor illumination
• Bulb not turning on when the oven is in use
• Error codes displayed on the control panel

Replace your faulty halogen light assembly with this genuine OEM part to restore your oven. This Samsung part can also be used on Kenmore/Sears appliances. 
 

This outer surface burner ring replaces the damaged or worn ring on a gas cooktop, restoring proper gas flow and burner alignment for safer, more even heating. Fits specified Samsung surface burners. What it does:

• Replaces a cracked, warped or corroded outer burner ring to re-establish correct burner geometry
• Helps restore consistent flame pattern and even cooking across the burner
• Can resolve issues like uneven heating or gas flame wandering at the burner edge
• Works with the matching inner burner and cap to form the complete burner assembly

• One outer surface burner ring

• Turn off gas supply and disconnect power to the appliance before servicing
• Allow all components to cool completely; burner parts may have sharp edges—wear gloves
• Remove burner cap and inner components, seat the new outer ring fully before reassembly