Dcv660eh0bb Parts

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

Includes 12 screws. Size: 8-18 ab.

The Dryer Heater Assembly is an OEM replacement part for GE dryers. It consists of the heating element and the necessary components to distribute and regulate the heat throughout the dryer drum.

Symptoms of a faulty dryer heater assembly include:

• Insufficient heat or no heat at all
• Extended drying times
• Burning smells during operation

A bad dryer heater assembly can be caused by normal wear and tear over time or damage due to blockages, electrical issues, or overheating. If you notice that your dryer is not heating properly, takes longer to dry clothes, or produces unusual odors, it may be time to replace the old or damaged heater assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.

The Thermostat is an OEM part for GE dryers. It monitors air temperatures inside the dryer drum during cycles to ensure they remain within a designated safe range. As a safety component, the thermostat automatically cuts power if temperatures get too high, protecting dryer components from damage.

Causes of a bad thermostat can include normal wear and tear over time from repeated heat cycles. Mineral buildup interference or electrical faults may also cause premature malfunction.

Symptoms of a faulty thermostat include:  

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set temperature points   
• Issues fully completing designated drying cycles  
• Potential overheating errors or safety trips

This genuine OEM GE replacement thermostat restores accurate temperature monitoring and controls. Compatible with some Hotpoint, RCA, and Kenmore models as well, it improves performance reliability and safety once installed. Replacing a faulty component prevents ongoing operational issues.

This electronic control assembly manages oven functions, timers and the display, restoring user interface and temperature control when the original control fails. It replaces a faulty control to get oven cycles and settings working again. What it does:

• Controls oven temperature, bake/broil functions, timers and the front display
• Sends and receives signals to start heating elements and manage bake cycles
• Commonly replaces controls that are unresponsive, show no display, or cause ovens to not heat or behave erratically
• Restores normal user-interface and programmed cooking functions when defective

• Disconnect power at the house breaker or unplug the appliance before servicing
• Handle the control assembly carefully to avoid damage from impact or static discharge
• Match the part number and visually confirm connector locations before installation

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.

The Thermistor Assembly is an OEM part for GE dryers. As an integrated sub-assembly, it includes multiple temperature-monitoring thermistors to comprehensively sense heat throughout cycles. 

Located in air inlets and outlets, these thermistors provide feedback to regulating components like the control board and heating elements. This allows for consistent thermal operation by maintaining intended temperatures.

Causes of failure can be normal component wear over repeated heat cycles. Mineral buildup, electrical faults, or accidental mishandling may also prematurely impact functioning.

Symptoms of a faulty thermistor assembly include: 

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set points
• Issues fully completing designated drying cycles
• Potential safety trips from inaccurate temperature readings

This genuine GE replacement ensures precise thermal regulation is fully restored. Compatible with some Hotpoint, RCA, and Kenmore dryer models as well, safety and performance reliability are improved.

This #8-32 x 1/2 machine screw is a direct-fit fastener used to secure panels and internal components in compatible appliances, restoring proper fit and eliminating loose or rattling parts. What it does:

• Secures panels, brackets, trim pieces and small internal assemblies where the factory screw is required
• Restores proper component alignment and prevents vibration-related noise
• Replaces missing or damaged mounting screws that allow parts to shift or come loose
• Matches standard #8-32 machine-thread fastener sizing commonly used in appliance assemblies

• Disconnect power and unplug the appliance before servicing to reduce shock risk
• Use the correct driver to avoid stripping the head; a magnetized screwdriver can help hold the screw
• Tighten until snug—do not overtighten to avoid damaging threads or panels
• Inspect mating threads and replace if damaged; replace with identical thread size and length

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This gas valve and pipe assembly controls and routes natural gas from the appliance inlet to the burner manifold, restoring proper fuel flow for ignition and stable burner operation. Designed as a direct-replacement service part. What it does

• Regulates and directs gas flow from the inlet to the oven/range burners.
• Enables proper ignition and stable flame for baking and broiling cycles.
• Works with the appliance's existing manifold and burner orifices to maintain correct gas delivery.

• Turn off gas supply and disconnect power before servicing; follow all safety procedures.
• After installation, check all fittings for leaks with an approved gas leak test (do not use an open flame).
• Replace only with the exact part specified for your appliance; inspect connections and gaskets and tighten to manufacturer torque specs.

Specs: 8-32 ca hxw 1/2