Dcvh515gfoww Parts

This OEM replacement part is the main control board for dryers. The main control board is the part that controls the functions of a dryer. It is the main component that sends signals to the dryer to perform its intended functions, controlling the desired dryer settings. If the dryer is no longer turning on, spinning properly, or effectively drying, it might be time to replace the main control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the dryer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board and be sure to take note of which wires go where by taking a photo with a phone camera. Then disconnect the air hose. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the air hose to the back of the control panel, and reconnect the wires into the back of the new control board.This genuine control board is compatible with General Electric, Hotpoint, RCA, and Sears/Kenmore brand dryers.

This ground screw secures the appliance chassis ground connection to the cabinet, restoring a reliable earth path for safe operation and reducing risk of electrical faults. Simple replacement keeps electrical components properly grounded. What it does

• Secures the ground wire or grounding strap to the appliance chassis to maintain a safe earth connection.
• Restores proper grounding when the original screw is missing, loose, or corroded.
• Helps prevent intermittent power/grounding issues and reduces risk of electrical arcing at the chassis connection.
• Works wherever a dedicated grounding point is required on the cabinet or frame.

• Single ground screw

• Always disconnect power (unplug or switch off circuit breaker) before servicing electrical connections.
• Verify chassis is de-energized and wear appropriate PPE when working on electrical parts.
• Use the correct driver bit and size to avoid stripping the screw; tighten securely but avoid over-torquing.
• Replace corroded grounding hardware and ensure the ground wire/strap has clean metal-to-metal contact.

This valve elbow redirects the appliance's water line to the inlet valve, providing a secure 90° connection to help prevent kinks and ensure consistent water flow. Simple, compact replacement for a worn or damaged elbow. What it does

• Redirects the water supply line to the appliance inlet valve for a neat, low-profile connection
• Helps prevent kinking or strain at the inlet connection that can lead to leaks
• Restores proper water routing when the original elbow is cracked, broken, or leaking
• Resolves symptoms such as visible leaks at the valve connection or reduced/disrupted water flow to dispensers or ice makers

• Turn off water supply and unplug the appliance before beginning work
• Drain residual water from the line before removing the old elbow to minimize spills
• Inspect the inlet fittings and water line for damage; replace any worn tubing or gaskets
• Use appropriate tools and replacement gaskets; hand-tighten fittings and check for leaks after restoring water

This door gasket is the flexible rubber seal that mounts around the refrigerator door to maintain an airtight seal, helping preserve internal temperatures and reduce energy loss from leaks. What it does:

• Seals the gap between the refrigerator door and cabinet to keep cold air inside.
• Prevents moisture intrusion, reducing frost, condensation, and excessive compressor run time.
• Restores proper door contact when original gasket is cracked, torn, warped, or no longer seals.
• Common symptoms: visible gaps, light showing around closed door, frost buildup, or higher-than-normal interior temperatures.

• Disconnect power to the appliance before beginning any work.
• Remove the old gasket and clean the door channel; inspect the mounting surface for damage.
• Press the new gasket into the channel starting at the corners, working around the door for an even fit; warm the gasket slightly (hair dryer on low) if needed to help seat it.
• Avoid sharp tools that can tear the gasket.

This motor and blower assembly moves air through the dryer to remove moisture and allow proper airflow. Replacing a worn or damaged assembly restores airflow and reduces drying time and overheating risk. What it does:

• Spins the blower wheel to circulate air through the drum and vent system
• Restores normal airflow when a failing motor or damaged blower causes weak or no air movement
• Reduces unusual noise caused by worn bearings, loose blower wheel, or motor issues
• Helps prevent overheating from restricted or insufficient airflow

• Disconnect power before servicing; this part requires access to the dryer cabinet
• Inspect wiring, mounting hardware, and venting while replacing the assembly

This screw back housing is a rear housing piece that holds and aligns screws and fasteners on the appliance's rear panel, helping maintain proper panel fit and component placement for safe, quiet operation. What it does:

• Secures rear-panel screws and fasteners to keep the back panel stable and aligned
• Supports adjacent components to prevent rubbing, vibration, or rattling noises
• Restores proper panel fit that can affect airflow or clearance around internal parts
• Helps prevent loose or misaligned panels that could expose wiring or components

• Always disconnect power before attempting any repair.
• Remove the rear access panel and keep track of screws and fasteners; note orientation before removing the old housing.
• Replace with the exact OEM part and reuse correct screws; do not overtighten to avoid stripping the housing.
• If adjacent clips or fasteners are damaged, inspect and replace them to ensure a secure fit.

This Nut-Strip Door Guide secures the door guide/strip to the appliance, helping keep the door aligned and operating smoothly. Replace a worn or missing nut to restore proper fit and prevent the guide from loosening. What it does

• Fastens the door guide/strip to the appliance frame or door
• Keeps the door guide stable to maintain proper door alignment
• Helps prevent the guide or trim strip from shifting or falling off
• Commonly replaced when the guide is loose, missing, or stripped

• Disconnect power to the appliance before beginning any repair.
• Use appropriate hand tools (screwdriver/socket) and avoid over-tightening to prevent damage.
• Inspect the door guide/strip and surrounding fasteners; replace any damaged parts for proper fit.

This motor strap secures the appliance motor to the cabinet, keeping the motor stable during operation to reduce vibration and noise. Use this replacement to restore proper motor positioning and support in compatible models. What it does:

• Holds the motor firmly in place to prevent movement or shifting during use
• Helps reduce vibration and associated noise caused by a loose motor
• Maintains correct motor alignment so belts and linkages run smoothly
• Commonly used when a worn or broken strap allows motor sag or misalignment

• One motor mounting/retaining strap

• Disconnect power to the appliance before beginning any work
• Inspect mounting points and fasteners; replace any damaged hardware as needed
• Secure strap to the motor and cabinet using the original mounting holes and recommended hardware

This levelling leg support bracket secures and stabilizes an appliance leg to keep the appliance level and steady on uneven floors. Restores proper footing to reduce rocking and improve door and drawer alignment. What it does:

• Holds the adjustable levelling leg in place so the appliance sits level and stable
• Helps stop rocking, tipping, and uneven operation caused by a loose or damaged bracket
• Restores proper appliance alignment to improve door and drawer sealing and operation
• Works with the factory levelling leg assembly to transfer weight to the cabinet/frame

• Designed for use with the factory levelling leg assembly;
• Turn off and unplug the appliance and empty any contents before working underneath
• Use basic hand tools; avoid forcing parts to prevent damage to cabinet or fasteners
• If mounting fasteners are damaged or missing, replace them with OEM-equivalent hardware