Need Help?
Call or text
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
Connects motor to drum for rotation. Replace if dryer won't start, makes noise, or drum doesn't turn. Confirm fit with your model number before ordering.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Dryer door won't stay closed? This door latch secures the door and activates the safety switch. Easy snap-in repair, typically 5-15 minutes.
If your dryer won't heat properly or makes squeaking noises, the blower wheel may be worn or damaged. Moderate DIY repair that restores air circulation.
New wheel didn't look different than the other wheel, but we put it on, it works and we're very happy. Read more
Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
Dryer won't start or hums but drum doesn't turn? This drive motor powers the drum and blower. Moderate DIY repair with video guide available.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Supports the dryer drum on its rear shaft. Replace if you hear grinding, squeaking, or clunking noises during operation. Confirm fit with your model.
Maintains belt tension for smooth drum rotation. Replace if the pulley is cracked, worn, or the nylon bushing is broken to restore proper operation.
I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside. Read more
Black hex washer screw for securing range components like door trim, control panels, and internal brackets. Replace missing or stripped screws during repairs.
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.
I cut power to the dryer. I removed the face of the dryer. I then removed the felt mounts beneath the drum. I removed the old strips of felt and cut the new seal to fit both mounts. I then remounted the felt mounts and replaced the face. Read more
Adjustable leveling leg that installs on the bottom of your dryer to stabilize and level the unit. Replace missing, broken, or worn legs. Easy DIY.
Installed the missing legs. Very east to do Read more
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.
Replace missing or stripped mounting screws in your refrigerator. This 12-pack of 8-32 thread screws secures panels, brackets, and components.
Replaces a worn, damaged, or misaligned dryer motor pulley. Guides the drive belt and transfers motor power to the drum for proper rotation.
Replaced belt, pulley with a 4 grove pulley. Pulley that was on there was a 3 grove pulley, Had to cut the old one off, Press on to shaft. Replaced rear drum bearing. Bearing was locked on with a snap ring. Access to it from a removable plate on the back side of dryer. Reset belt and idler puller by removing a long back plate on the bottom rear side of the dryer. None of this was shown in your Video. Read more
Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.