Ddt95ssjoss Parts

This diverter assembly kit controls the dishwasher's wash-water routing. It switches flow between spray arms for targeted cleaning. Replacing a failed diverter restores proper water distribution and helps recover normal wash performance.

• Directs wash water between lower and upper/middle spray arms as the cycle advances
• Works with the control to provide zone/alternating spray for efficient cleaning
• Failure can cause poor cleaning on one rack or water spraying from only one arm
• May produce repeated clicking/grinding from the sump area or extended cycles while indexing

• Disconnect power and shut off water supply before servicing; expect some residual water
• Access the diverter at the sump/pump area; follow your model's service procedures
• Ensure seals/O-rings are properly seated and parts are aligned before tightening
• Run a short test cycle to check for leaks and confirm both racks receive spray

This right-hand roller cover is the small retainer that locks a dishwasher rack roller onto its mount. Replacing a cracked or missing cover restores smooth, stable rack movement and helps prevent the roller from working loose during use.

• Secures the right-hand rack roller to its axle/mount
• Helps the rack slide smoothly and stay level
• Replaces covers that are cracked, worn, or missing
• Symptoms include: rack binding on one side, tilting/dropping, rattling, or a roller that pops off

• Disconnect power and shut off water before servicing
• Pull the rack forward and remove if needed to access the roller area
• Release the old cover's locking tabs; align and snap the new cover into place on the right-hand side
• Ensure the rack rolls smoothly and sits level; right- and left-hand pieces are not interchangeable

This 10-32 x 9/16 machine screw secures dishwasher components and panels. Replacing a missing or stripped fastener restores a tight fit, reduces vibration/rattles, and keeps assemblies properly aligned for reliable operation.

• Secures panels, brackets, or internal assemblies using a 10-32 machine thread
• Replaces lost, corroded, or stripped screws
• Can help resolve looseness or rattling from a loose mounting point
• Correct 9/16-inch length helps maintain proper spacing and alignment

• Disconnect power at the breaker before servicing
• Use the appropriate driver for the screw head; start threads by hand to avoid cross-threading
• Tighten snugly but do not overtighten to prevent stripping threads or damaging mating parts
• Compare to the original fastener to matching thread and length

• Thread size: 10-32
• Length: 9/16 inch

The Hub is an OEM replacement part for GE dishwashers. It is the central mechanism which attaches to the tub and facilitates rotation of the upper spray arm above dishes. 

Causes of a bad hub include wear from years of repeated rotation, accumulation of hard water scale deposits inside moving parts, or accidental impact damage. This reduces proper function over time.

Symptoms of a bad hub include:

• Loud clunking or grinding noises from the center mechanism
• Reduced cleaning performance on upper racks or portions of dishes  
• Dishes showing water spots or soil in sections not adequately rinsed
• Inability to attach or move the upper spray arm assembly smoothly

This OEM GE hub replacement is also compatible with Crosley, and KitchenAid models.

This replacement upper spray arm assembly restores full wash coverage to the top of your dishwasher. It spins under water pressure, directing jets across the racks so dishes come out cleaner with fewer spots and leftover food.

• Distributes pressurized water through its jets to clean the upper section
• Replaces a spray arm that is cracked, warped, clogged, or not rotating freely
• Typical symptoms: poor cleaning on the top rack, residue left on dishes, or rattling from the arm striking items
• Restores even spray coverage when properly installed and unobstructed

• Disconnect power and water supply before servicing
• Release and remove the old upper arm (tab/clip/retainer varies by model); clear debris from the hub/feed area and transfer any reusable hardware
• Seat the new arm fully and confirm it spins freely before restoring service

The Inner Door Panel is an OEM part for GE dishwashers. It serves as the inner lining of the dishwasher door, ensuring a watertight seal and supporting components like the detergent dispenser and vent assembly.

Common causes of a bad inner door panel include wear and tear from regular use, exposure to high temperatures and harsh detergents, or physical impacts that cause cracks or warping.

Symptoms of a bad Inner Door Panel include:

• Water leaking from the door area during operation
• Difficulty in opening or closing the door properly
• Visible cracks, warping, or other damage to the panel
• Malfunctioning detergent dispenser or other door-mounted components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher main control board kit is the central circuit board that directs all wash functions. Replacing a failed board restores proper power distribution and timing so cycles start, advance, and finish correctly, helping prevent intermittent shutdowns and erratic operation. What it does:

• Controls cycle timing and communicates with sensors
• Distributes power to the wash motor, drain pump, inlet valve, and heater
• Works with the door latch and user interface to start/stop the cycle
• Failure may cause no power/won't start, stalled cycles, blinking lights/error codes, or incorrect filling, draining, or heating

• One main control board kit

• Disconnect power at the circuit breaker; turn off water if moving the dishwasher for access
• Board is typically in a housing beneath the unit—use ESD precautions and keep connections dry
• Photograph/label wire harnesses; transfer connectors one at a time to the new board
• Restore power and run a test or rinse cycle to proper operation

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This wash pump kit restores the main circulation in P2B-platform dishwashers, moving water through the spray arms for effective cleaning. Replace a failed or noisy pump to bring back consistent wash performance.

• Circulates wash water through the spray arms during wash and rinse cycles
• Maintains proper spray flow for reliable cleaning results
• Replaces a seized, weak, or noisy circulation pump
• Typical symptoms: poor cleaning, weak/no spray, loud humming or grinding, or leaks near the pump area

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the toe kick and slide the dishwasher out as needed to access the pump from below
• Keep towels or a shallow pan ready; disconnect wiring and hoses carefully, comparing parts and transferring any model-specific clamps or seals as required
• Restore power and water, check for leaks, and run a test cycle to verify operation

This tub insulation is the replacement foam/fiber wrap that lines the dryer drum area to help retain heat, reduce exterior cabinet temperature, and dampen operation noise for more efficient, quieter drying. What it does:

• Wraps around the dryer drum/tub to help limit heat loss during cycles
• Helps reduce cabinet surface temperature for safer operation
• Dampens vibration and operating noise from the rotating drum
• Supports consistent drying performance by improving heat retention
• Useful when original insulation is damaged, torn, or missing

• Disconnect power (and gas supply for gas dryers) before servicing
• Access requires removing the dryer cabinet or drum per OEM instructions
• Handle carefully—use gloves and eye protection; avoid breathing any loose fibers
• Reinstall with original fasteners and seal as needed to maintain drum clearance

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

This adapter plate is a molded interface in the wash system that secures and seals components so water pressure is routed correctly. Replacing a cracked or warped plate helps stop leaks and restore proper spray performance.

• Connects and supports wash-system components at the sump/water-feed interface
• Maintains a reliable seal to help prevent leaks
• Helps direct wash water to the spray arms for effective cleaning
• Replace if cracked, warped, or stripped; symptoms can include leaks, weak spray, or a loose spray arm

• Disconnect power and water supply before servicing
• Remove the lower rack and related wash components to access the plate; note the order of parts for reassembly
• Reuse existing seals and fasteners in their original positions; seat the plate evenly and tighten hardware snugly, not overtight
• Run a brief test cycle and inspect for leaks before full use

This Roller and Bracket Assembly is an OEM part for GE dishwashers. It is an essential component in the dishwasher's rack system, providing smooth and stable movement for the racks as they slide in and out. This assembly includes both the rollers and the brackets that attach them to the dishwasher racks, ensuring effortless gliding and reliable support. 

The need to replace the roller and bracket assembly can arise from wear and tear, damage, or misalignment. 

Symptoms of a faulty Roller and Bracket Assembly include:

• Difficulty in sliding the racks in and out smoothly.
• Racks getting stuck or derailing during movement.
• Noticeable wear or damage to the rollers or brackets.
• Unusual noises when moving the dishwasher racks.
• Loosening or detachment of the assembly from the racks.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This conduit seal fits the dishwasher's water-feed conduit connection, keeping wash water contained and pressure steady to the spray arms. Replacing a worn seal helps address leaks and maintain reliable cleaning performance.

• Seals the joint where the dishwasher's water feed conduit/tube connects within the wash system
• Helps prevent water leaks at the conduit connection point
• Maintains proper wash pressure for consistent spray performance
• Common signs of failure: drips beneath the unit, visible cracks/flattening, or a loose-fitting old seal

• Disconnect power and shut off the water supply before servicing
• Access the conduit connection (location varies by model), remove the old seal, and clean mating surfaces
• Lightly moisten the new seal to ease installation and seat it fully
• Reassemble and run a brief cycle to check for leaks