Ddt95ssjoss Parts

This sump manifold directs wash and drain water into the washer's pump assembly, ensuring proper drainage and circulation. Replaces a cracked or leaky housing to restore reliable water flow and help prevent leaks. What it does:

• Channels tub water to the drain pump so the washer can drain properly.
• Prevents leaks by sealing the pump inlet and connections.
• Commonly replaced when the manifold is cracked, warped, or leaking.
• Helps resolve symptoms like water pooling in the washer tub or visible leaks under the appliance.

• Disconnect power and water supply before starting any repair.
• Drain remaining water from the washer and remove front or rear access panel as needed.
• Inspect and replace any worn gaskets or seals when installing the new manifold.
• Tighten connections evenly; avoid overtightening plastic fasteners to prevent cracking.

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

This bracket support hinge helps secure and guide the appliance hinge assembly, restoring proper door alignment and reliable movement. It replaces a worn or damaged hinge support to improve fit and operation. What it does:

• Supports the hinge assembly to maintain correct door alignment
• Reduces door sag, binding, or uneven closing caused by a damaged bracket
• Restores smooth hinge movement and helps prevent further wear to hinge components
• Commonly used when the door feels loose or the hinge appears bent or broken

• One bracket support hinge

• Turn off and unplug the appliance before starting any repair
• Remove surrounding panels or trim as needed to access the hinge per your model's service instructions
• Use appropriate tools and keep fasteners organized for reassembly
• Inspect and replace additional components as needed

This wiring harness assembly connects and routes power and control signals for the appliance's AC components, restoring reliable electrical connections and proper operation when the original harness is damaged or worn. What it does:

• Provides the factory wiring path for AC-related components so they receive correct power and signals
• Replaces frayed, damaged, or burnt wires that can cause intermittent operation or failures
• Helps eliminate symptoms such as components not powering on, intermittent operation, or electrical arcing at connections
• Ensures connector fit and terminal alignment for a secure electrical connection

• Disconnect power before beginning any repair to avoid electrical shock
• Note or photograph wire routing and connector positions before removal for correct reinstallation
• Secure harness with existing clips or fasteners to prevent chafing and strain on terminals

This rail and end cap assembly replaces a worn or broken rack rail so the appliance rack glides smoothly and stays secured. It restores proper support and reduces catching, slipping, or noisy movement during use. What it does:

• Supports the appliance rack and provides a smooth sliding track.
• Replaces damaged or cracked rails and end caps that cause the rack to catch or bind.
• Helps prevent the rack from slipping off the track or dropping when extended.
• Reduces grinding, scraping, or other abnormal noises tied to worn rail components.

• Turn off power to the appliance (unplug or shut off the breaker) before starting.
• Remove the rack and align the rail with the track; snap or slide the end cap into place per the appliance's service instructions.
• Use basic hand tools if needed; avoid excessive force to prevent breakage.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

A fixed mounting bracket that secures and stabilizes a component or panel in place, helping prevent movement and vibration for reliable appliance operation. Simple, durable replacement for worn or damaged brackets. What it does:

• Holds a panel, trim, or assembly securely to the appliance frame
• Keeps parts aligned to prevent rubbing, rattling, or misfit
• Restores proper support when an original bracket is bent, cracked, or broken
• Helps reduce noise caused by loose or unstable components

• Disconnect power (and water if applicable) before starting work
• Use the factory fasteners or equivalent-size screws to secure the bracket
• Inspect mating surfaces and hardware for damage; replace any stripped screws

This vent conduit assembly routes exhaust from the dryer to the home vent, restoring proper airflow and helping the appliance vent safely. It replaces a damaged, crushed, or disconnected dryer vent channel to improve drying performance and reduce lint buildup. What it does:

• Channels dryer exhaust from the appliance to the wall vent
• Prevents restricted airflow caused by crushed or separated vent tubing
• Helps reduce long dry times and overheating symptoms
• Lowers risk of lint buildup and related odors near the dryer

• Disconnect power (and gas supply for gas dryers) before beginning service
• Verify correct alignment and secure with appropriate clamps or fasteners
• Inspect adjacent venting and clean lint from vent path while replacing

This control box bottom is the lower housing piece that secures and protects the appliance control board and related components. It restores a stable mounting surface and helps keep electronics shielded from vibration and debris. What it does:

• Provides the lower half of the control box housing to support and protect the control board
• Keeps wiring and connectors routed and held in place to prevent strain
• Replaces cracked, broken or warped housing that can expose electronics
• Helps stop rattling or movement of the control assembly that can cause intermittent controls

• Control box bottom

• Power off and unplug the appliance before starting any repair
• Handle the control board and connectors carefully to avoid electrostatic or mechanical damage
• This part typically installs with screws or clips; retain fasteners and note their locations during disassembly
• Inspect and address the electronics before reassembly

This inner door panel replaces the inner-facing panel of the oven door to restore a clean barrier between the oven cavity and the outer door. It helps keep heat inside and protects the outer assembly from spills and grime. What it does:

• Replaces damaged, cracked or heavily stained inner oven door panel
• Restores a proper seal and barrier between the oven cavity and door assembly
• Helps reduce heat loss and prevents food splatter from reaching the outer door
• Matches OEM fit and mounting locations for direct replacement

• One inner door panel

• High-level replacement; remove oven door per manufacturer instructions before disassembly
• Avoid touching glass edges; wear cut-resistant gloves and eye protection
• Keep track of screws and clips during reassembly; use manufacturer torque recommendations

This console cover graphic is the printed overlay that fits over the dryer control panel to restore button labels and the finished appearance. It protects the control surface and makes settings easy to read. What it does:

• Restores legible labels and indicators on the control panel so cycles and options are clear
• Protects underlying switches and electronics from light wear and spills
• Replaces faded, cracked, or peeled graphics that make controls hard to read
• Helps cosmetically renew the appliance for a cleaner, like-new look

• Disconnect power to the appliance before beginning any work
• Removal typically requires opening or removing the console — keep screws and small parts organized
• Align carefully and avoid stretching or creasing the graphic during installation

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This tub trim replaces the decorative and protective ring around the appliance tub opening to restore a finished look and help keep the door seal aligned. It's a direct-fit cosmetic trim for specified GE tubs. What it does

• Covers the gap between the tub and door opening for a clean finished appearance
• Protects the tub edge and door seal from wear and fabric snags
• Helps maintain a snug seal by holding gasket edges in place
• Fixes issues like visible damage, cracks, or missing trim that affect appearance

• One tub trim (black/stainless) as shown

• Disconnect power and, if applicable, water supply before starting repairs
• Installation typically requires removing the door or front panel and snapping or screwing the trim into place — have basic hand tools ready
• Wear gloves to protect hands from sharp edges during removal/installation

This manual floor plate is the replacement cover that mounts at the appliance base to protect internal components and provide a finished surface. It restores the dryer's base appearance and helps prevent debris from entering the cabinet. What it does:

• Covers and protects the lower cabinet opening and components from dust and lint
• Helps maintain proper clearance and a finished look at the dryer base
• Replaces damaged, bent, or missing base plates that allow debris entry
• Can reduce rattles or vibration caused by a loose or warped floor plate

• One floor plate

• Disconnect power (and gas, if applicable) before servicing to avoid shock or injury
• Remove the dryer front or lower access panel per manufacturer instructions to access mounting screws
• Use correct-size screws and tighten to manufacturer torque; avoid over-bending the plate during installation

Left side roller cover.