Dley1701e Parts

Note: This is the vertical bar connector.
 

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly while staying aligned for a proper seal. Replacing a worn or bent hinge restores consistent door action and helps prevent latch and sealing issues.

• Provides the pivot point that allows the door to open and close
• Maintains door alignment so the latch and gasket engage correctly
• Helps prevent sagging, rubbing, and poor sealing
• Common symptoms: drooping or loose door, difficulty closing, binding/squeaking, visible damage

• Disconnect power before servicing; allow any hot surfaces to cool
• Support the door during removal/installation to prevent damage or injury
• Transfer any spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and gasket contact; adjust per service information if needed

This door gasket forms a watertight seal between the appliance's tub opening and the door, keeping wash water contained during operation. Replacing a worn seal helps stop leaks and protects floors and nearby cabinetry. What it does:

• Creates a tight, water-resistant seal around the door opening
• Replaces a torn, cracked, flattened, or deformed gasket that can leak
• Common symptoms: drips from the door area, puddles at the front corners, visible damage or mildew on the seal
• Restores proper door compression and helps prevent moisture/steam from escaping

• 1 door gasket

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel and mating surfaces
• Seat the new gasket evenly; ensure it is fully pressed into its channel (some models use retaining bands or clips—transfer and reinstall as removed)
• Close the door to check for uniform contact, then run a short cycle to verify no leaks

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

This hinge bracket anchors the door hinge to the appliance cabinet, keeping the door aligned for smooth opening and a reliable seal. Replacing a bent or worn bracket restores proper door movement and reduces rubbing, sagging, and gaps.

• Secures the hinge to the cabinet/frame and supports door weight during operation
• Helps maintain door alignment for consistent gasket contact
• Restores smooth pivoting of the door
• Common signs it's needed: door sagging or rubbing, popping/creaking at the hinge area, loose mounting, or visible damage to the bracket

• Disconnect power; if applicable, shut off water
• Support the door while servicing; a second person is recommended
• Note hinge/bracket orientation and transfer any spacers/shims and hardware from the old bracket
• Tighten mounting screws evenly and verify door gaps and seal contact before restoring power

This damper assembly mounts at the microwave's exhaust outlet to direct airflow outside and block backdraft when the fan is off. Replacing a cracked or warped damper restores venting performance and helps reduce drafts and rattling noise.

• Opens with blower airflow and closes when off to help prevent outside air from entering through the duct
• Directs steam, smoke, and cooking odors to the exhaust path
• Helps reduce drafts/backdraft when the fan is not running
• Common failure signs: weak venting, flap stuck open/closed, or rattling/flapping noises

• Disconnect power at the breaker; if over-the-range, support the unit per manufacturer instructions
• Remove the vent grille/top cover to access the outlet and take out the old damper; reuse existing hardware as needed
• Match the new damper's orientation to the original so the flap opens with airflow and moves freely
• Beware sharp sheet-metal edges; wear cut-resistant gloves and test the fan after reassembly to confirm proper operation

The Water Valve is an OEM part for LG dryers. This valve controls the water supply to the dryer's steam setting which helps reduce wrinkles and refresh clothing.

Causes of failure can be mineral buildup overtime restricting flow, damage from freezing during winter months, or worn internal seals and mechanisms.

Symptoms of a bad water valve include:

• Inability to select or utilize the steam cycle
• Drips or leaks at the water inlet port
• Erratic water pressure during steam cycles
• Steam levels that fluctuate or cut off unexpectedly

This OEM LG part is also compatible with some Kenmore models.

Note: This is the horizontal bar connector.

This hinge bracket secures the door hinge assembly to the cabinet, restoring proper door support and alignment for smooth opening and a tight seal. Use it when the hinge area is cracked, worn, or no longer holding the door square. What it does

• Supports and anchors the door hinge so the door stays aligned and closes properly
• Replaces a cracked, broken, or worn bracket that causes door sag or misalignment
• Helps stop rubbing, gaps, and uneven sealing caused by a loose or damaged hinge area
• Works as a direct-fit structural part for the hinge assembly on compatible LG units

• One hinge bracket

• Disconnect power to the appliance and empty the door before starting; have a helper support the door during removal/installation
• Use the correct screwdriver/socket size to remove and reinstall mounting fasteners; do not overtighten
• Inspect hinge pins, screws, and surrounding mounting points; replace any damaged hardware
• After installation, verify door alignment and seal; adjust hinge position if needed following OEM guidance

This hinge bracket secures the refrigerator door hinge to the cabinet, restoring stable door alignment and smooth opening. It replaces a worn or damaged mounting bracket so the door closes evenly and stays properly supported. What it does:

• Provides the structural mounting point for the door hinge to attach to the cabinet
• Restores proper door alignment and prevents sagging or uneven gaps
• Reduces binding and noisy operation caused by a bent or broken bracket
• Helps ensure the door seals correctly for consistent cooling performance

• One hinge bracket

• Designed for a direct replacement; use appropriate tools and support the door before removing hinge fasteners to avoid injury or damage
• Disconnect power and remove food from door edges if required by the manufacturer's service instructions
• Retain original screws or order as specified by the OEM

This replacement locker handle restores a secure grip and reliable latch operation on the appliance door or access panel. It replaces a cracked, loose, or missing handle so the door opens and closes smoothly. What it does:

• Provides a firm handhold for opening and closing the door or access panel
• Secures the door latch area to help maintain proper closure
• Replaces broken, cracked, or worn handles that are hard to grip
• Helps reduce rattling or loose-feeling door operation

• One locker handle

• Disconnect power to the appliance before beginning any repair
• Remove any trim or access panels as needed; use basic hand tools
• Handle may attach with clips or screws — keep hardware organized for reassembly
• Test door operation after installation; if fit feels incorrect, check part number and orientation