Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix dryer display not lighting up or unresponsive control buttons. This power control board restores front-panel display and button functions.
Plastic retainer clip that secures the top cabinet panel to the washer chassis. Replace if cracked, broken, or missing to restore alignment and prevent rattling.
I replaced the fill valve assembly with a new one. Had to look carefully at the parts diagrams to make sure I ordered the right one since the serial number break old vs. new didn't seem to match the number on my machine. On this particular machine you don't need to pull it out too far from the wall-leave the hoses connected to the valve, remove the screw holding the valve bracket, and pull into the washing machine where you can easily access the hose ends. A putty knife is needed to open... Read more
Fix TE1 error codes and unresponsive controls with this main control board. Regulates temperature, moisture sensing, and all dryer functions. 1-2 hour repair.
Dryer won't start or stops mid-cycle? This main power control board manages electrical functions and restores operation. Moderate DIY repair.
If your dryer drum stopped turning, a worn motor bracket may be the cause. This bracket holds the motor and tension pulley securely in place.
Tension pully screw fell out of the motor bracket. Upon inspection, the hole was worn and would not hold the screw tightly. New bracket installed with a new belt just because it was already apart. Runs great now! The bracket was half the price of a competing on-line store. Read more
Duct hose that connects your dryer's blower to the exhaust vent. Replace if cracked, torn, or disconnected to restore proper airflow and ventilation.
Rear support assembly stabilizes your dryer's housing and aligns internal components. Replace if cracked, broken, or worn to prevent noise and vibration.
Replaced the roller and shaft. The roller had worn 1/4 of the way through the support shaft. Read more
Upper cavity plate installs inside the top of the dryer drum area. Replace if cracked, broken, or missing to restore proper coverage and appearance.
Fix leaks or water pooling inside your dryer with this inlet pipe assembly. Routes water to the dispenser and ice maker, restoring proper flow.
Replace your dryer's control panel assembly to restore responsive buttons and accurate display readings. Confirm fit with your model number before ordering.
Secures the door hinge assembly to the dryer cabinet. Replace if your bracket is cracked, bent, or broken to restore proper door alignment and support.
If your dryer door or control switch is loose or misaligned, this retainer clip holds the switch securely in place for reliable operation. Simple fix.
Supports the front of the dryer drum for smooth rotation. Replace if drum is noisy, wobbling, or causes overheating. Verify fit with your model number.
New glides, idler had a crack, blower retaining ring was gone. And a good clean out. Like new again for 2 hours and $77.00 Read more
Appliance won't start or trips breaker? This ground screw secures the grounding conductor to the chassis for safe electrical connection. Simple fix.
I ordered a new heating element and two other parts that attached to the heating element. I discovered a wire that broke off which caused the element not to work so I had to put a new female splicer on the broken wire then replaced the element and reattached the wires and everything worked. Read more
Fix loose or rattling parts with this 1/4-20 nut. Secures components in dryers, washers, and microwaves. Quick 5-minute repair restores stability.
After watching the repair video I opened up the dryer without any problems and found that the belt tension pully bearing failed and the mount arm had an excessive amount play in it. So armed with the part numbers I found here I went down to the local parts store and found that they did not stock the parts but could get them in a week. I went home and ordered them on line and had them the next day. I did vary from the video a bit. I uncliped the motor wire connector and removed the two screws... Read more
Secures wire harness connections in your washer. Replace if clip is broken, cracked, or missing to prevent loose wiring. Verify fit with your model number.