Dlg7051v Parts

Note: This is the vertical bar connector.
 

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly while staying aligned for a proper seal. Replacing a worn or bent hinge restores consistent door action and helps prevent latch and sealing issues.

• Provides the pivot point that allows the door to open and close
• Maintains door alignment so the latch and gasket engage correctly
• Helps prevent sagging, rubbing, and poor sealing
• Common symptoms: drooping or loose door, difficulty closing, binding/squeaking, visible damage

• Disconnect power before servicing; allow any hot surfaces to cool
• Support the door during removal/installation to prevent damage or injury
• Transfer any spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and gasket contact; adjust per service information if needed

This door gasket forms a watertight seal between the appliance's tub opening and the door, keeping wash water contained during operation. Replacing a worn seal helps stop leaks and protects floors and nearby cabinetry. What it does:

• Creates a tight, water-resistant seal around the door opening
• Replaces a torn, cracked, flattened, or deformed gasket that can leak
• Common symptoms: drips from the door area, puddles at the front corners, visible damage or mildew on the seal
• Restores proper door compression and helps prevent moisture/steam from escaping

• 1 door gasket

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel and mating surfaces
• Seat the new gasket evenly; ensure it is fully pressed into its channel (some models use retaining bands or clips—transfer and reinstall as removed)
• Close the door to check for uniform contact, then run a short cycle to verify no leaks

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

This hinge bracket anchors the door hinge to the appliance cabinet, keeping the door aligned for smooth opening and a reliable seal. Replacing a bent or worn bracket restores proper door movement and reduces rubbing, sagging, and gaps.

• Secures the hinge to the cabinet/frame and supports door weight during operation
• Helps maintain door alignment for consistent gasket contact
• Restores smooth pivoting of the door
• Common signs it's needed: door sagging or rubbing, popping/creaking at the hinge area, loose mounting, or visible damage to the bracket

• Disconnect power; if applicable, shut off water
• Support the door while servicing; a second person is recommended
• Note hinge/bracket orientation and transfer any spacers/shims and hardware from the old bracket
• Tighten mounting screws evenly and verify door gaps and seal contact before restoring power

This damper assembly mounts at the microwave's exhaust outlet to direct airflow outside and block backdraft when the fan is off. Replacing a cracked or warped damper restores venting performance and helps reduce drafts and rattling noise.

• Opens with blower airflow and closes when off to help prevent outside air from entering through the duct
• Directs steam, smoke, and cooking odors to the exhaust path
• Helps reduce drafts/backdraft when the fan is not running
• Common failure signs: weak venting, flap stuck open/closed, or rattling/flapping noises

• Disconnect power at the breaker; if over-the-range, support the unit per manufacturer instructions
• Remove the vent grille/top cover to access the outlet and take out the old damper; reuse existing hardware as needed
• Match the new damper's orientation to the original so the flap opens with airflow and moves freely
• Beware sharp sheet-metal edges; wear cut-resistant gloves and test the fan after reassembly to confirm proper operation

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

A manufacturer-configured replacement component designed to restore the appliance's original factory settings and functions. Use this part when a model-specific, pre-configured module is required to return correct operation. What it does:

• Provides the factory-specific configuration and setup programmed by the manufacturer
• Restores functions controlled by the module when configuration or programming is corrupted
• Resolves symptoms such as appliance not starting, control panel unresponsive, or intermittent/erratic operation linked to configuration errors
• Ensures compatibility with model-specific features when the appliance requires a pre-configured assembly

• Disconnect power to the appliance before starting any work
• Handle electronics carefully; observe electrostatic discharge (ESD) precautions for circuit boards or modules
• Match connectors and mounting locations to the original part; do not force connectors

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and vibration for reliable operation. It's a simple replacement part that restores proper fit and stability. What it does:

• Secures and supports nearby components or assemblies to prevent shifting
• Reduces vibration and rattling that can cause noise or wear
• Helps maintain correct alignment for connected parts to operate smoothly
• Restores original component retention after damage or loss of the bracket

• Disconnect power to the appliance before beginning any repair
• Basic hand tools may be required; handle small parts carefully to avoid loss
• Inspect surrounding clips and fasteners; replace any that are damaged

This hinge bracket secures the door hinge assembly to the cabinet, restoring proper door support and alignment for smooth opening and a tight seal. Use it when the hinge area is cracked, worn, or no longer holding the door square. What it does

• Supports and anchors the door hinge so the door stays aligned and closes properly
• Replaces a cracked, broken, or worn bracket that causes door sag or misalignment
• Helps stop rubbing, gaps, and uneven sealing caused by a loose or damaged hinge area
• Works as a direct-fit structural part for the hinge assembly on compatible LG units

• One hinge bracket

• Disconnect power to the appliance and empty the door before starting; have a helper support the door during removal/installation
• Use the correct screwdriver/socket size to remove and reinstall mounting fasteners; do not overtighten
• Inspect hinge pins, screws, and surrounding mounting points; replace any damaged hardware
• After installation, verify door alignment and seal; adjust hinge position if needed following OEM guidance