Dlg7601we Parts

This precision fastener is designed for specific locations on the appliance. Replacing a missing or damaged screw restores secure mounting and reduces vibration or rattling, helping panels and components stay properly aligned.

• Secures brackets, panels, and internal assemblies where this screw is specified
• Replaces stripped, rusted, or lost hardware
• Helps eliminate looseness, vibration, and noise
• Maintains proper fit and alignment of parts

• Disconnect power and shut off water/gas before servicing
• Use the correct driver; keep removed hardware organized for reassembly
• Do not overtighten; install into clean, undamaged threads
• Confirm location and quantity using your model's parts diagram

This cabinet hole cap plugs unused hinge or screw openings on the dryer cabinet. It restores a clean, finished look and helps keep lint and moisture out after a door reversal or service. What it does:

• Covers open hinge/screw holes on the dryer cabinet
• Helps block lint, dust, and moisture from entering through unused openings
• Restores a finished appearance; helps prevent snags around exposed holes
• Commonly replaced when a cap is missing, cracked, or loose

• 1 cabinet hole cap

• Disconnect power before working near the cabinet
• Remove any damaged cap and clean the opening
• Press the new cap into the hole until fully seated and flush
• Wear gloves; cabinet edges and holes can be sharp

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

The LAMP, LED is an OEM component specifically designed for LG dryers. It provides illumination inside the dryer drum, a crucial safety feature for easily viewing clothes during operation. Proper lighting allows users to monitor drying progress without hindering efficiency.

Causes of a bad LED lamp can include regular wear and tear over extended use, as well as potential electrical issues disrupting current flow to the lighting source.

Symptoms of a bad LED lamp include:

• Dim or completely absent lighting inside the dryer drum
• Inability to visually inspect clothes without opening the dryer door
• Premature ending of cycles due to detection of insufficient light  

The high-efficiency LED technology in this OEM part helps maximize useful life. Replace yours today to restore optimal usability. This LG replacement part is also compatible with Sears/Kenmore models.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

The Motor Bracket is an OEM part for LG dryers. This bracket securely holds the dryer motor in place. It maintains proper alignment and spacing of the motor to allow for smooth operation of the tumble cycle.

Causes of a bad motor bracket can include cracks or breaks developed over time from repeated use and vibration, or damage due to impact or improper installation.

Symptoms of a bad motor bracket include:

• Excessive noise or grinding sounds emanating from the motor area
• The dryer not rotating or tumbling clothes properly
• Increased movement or shaking of the motor
• Poor airflow and inefficient drying performance

This OEM LG part is also compatible with some Kenmore models.

This hinge support is a replacement mounting bracket that helps secure and stabilize a door hinge assembly for proper alignment and smooth opening. It restores correct hinge positioning to reduce sagging and uneven door movement. What it does:

• Supports the door hinge assembly to maintain proper door alignment
• Helps prevent door sagging, binding, and uneven gaps
• Provides a stable mounting point for hinge pins and related hardware
• Used when hinge mounting points are cracked, worn, or damaged

• Basic hand tools required; inspect surrounding hinge components and replace any damaged fasteners
• Tighten screws to secure the support but avoid over-torquing to prevent cracking
• Disconnect power or follow appliance-specific safety steps when working near electrical components

This display power control board assembly powers and controls the appliance display and front-panel electronics so the user interface responds correctly. Replaces a failed display control board to restore readable indicators and responsive controls. What it does:

• Supplies regulated power to the control panel and display modules.
• Manages display backlight and indicator LEDs so settings and status are visible.
• Helps resolve symptoms like a blank or unresponsive display, missing indicators, or intermittent panel behavior.
• Works as the replacement for the main display/control electronics—does not include user interface overlays or buttons unless listed below.

• One display power control board assembly.

• Disconnect power (unplug or shut off breaker) before accessing electronics to avoid shock or damage.
• Handle the board by edges and avoid touching contacts or components to prevent static damage.
• Verify matching part number on the old board before installation; connector positions should match the replacement.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This upper plate is the replaceable trim/cover that fits inside the top of the microwave cavity to protect internal components and help direct airflow. Replacing a damaged plate restores proper coverage and reduces debris buildup. What it does

• Covers and protects internal microwave components at the top of the cavity
• Helps maintain proper airflow and part alignment inside the oven
• Prevents food and debris from contacting internal wiring and electronics
• Reduces rattling or vibrations caused by a warped or loose plate
• Visible cracks, warping, or burn marks are common signs it needs replacement

• One upper plate as pictured

• Disconnect power at the wall and allow the oven to fully power down before servicing
• Remove fasteners or clips holding the old plate, align tabs, then secure the new plate with the original hardware
• Do not operate the microwave with covers removed; complete the repair

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

This display power control board assembly supplies and manages power to the appliance display and user interface so the control panel lights and touch/press controls operate correctly. It restores visible display and responsive control operation when the display electronics fail. What it does:

• Provides power and signal distribution to the control panel display and front-panel electronics
• Restores display illumination and responsiveness when the display is dark or unresponsive
• Helps stop intermittent display flicker, blank screens, or loss of control panel feedback
• Works with the main control system to show status and error information on the display

• One display power control board assembly

• Disconnect power to the appliance before starting — risk of electric shock
• Handle the board by the edges and avoid touching components; observe ESD precautions
• Replacing may require removing the control panel; keep screws and connectors organized