Du2000vlower Parts

A replacement shaft seal that restores the watertight seal where a rotating shaft passes through the tub or housing, helping prevent leaks and protecting bearings and internal components from moisture and contamination. What it does:

• Seals the gap around a rotating shaft to stop water from leaking out of the tub or housing.
• Helps keep grease and contaminants contained around bearings and shaft openings.
• Common symptom link: replace when you see water on the floor, visible leaks near the shaft, or wet/soiled bearing areas.
• Small, inexpensive part that prevents further damage to nearby components when installed promptly.

• Disconnect power and turn off water supply before beginning work; drain remaining water from the appliance.
• Access usually requires partial disassembly (remove panels/tub or transmission as applicable); follow OEM instructions.
• Inspect shaft and housing for wear or damage; clean mating surfaces before installing the new seal.
• Test appliance for leaks after reassembly and before returning to regular use.

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

This electric heating element generates the high heat needed for your appliance to reach operating temperatures, restoring normal heating performance and cycle effectiveness. Use the correct replacement for safe, reliable heat output. What it does:

• Heats the appliance's air or oven cavity so cycles reach intended temperatures
• Restores proper heating when the appliance runs but produces little or no heat
• Helps resolve long cycles or poor performance caused by a failed element
• Replaces a worn or open element that shows visible damage or electrical failure

• One heating element

• Disconnect all power before beginning service to avoid shock or injury
• Handle the element carefully to avoid bending or kinking the tubing/coil
• Verify electrical connections are secure and correct before restoring power

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

This replacement rack track restores smooth, stable rack movement and keeps the oven rack aligned while sliding in and out. It helps prevent rack sagging, binding, or uneven travel so food and cookware stay level and secure. What it does

• Guides and supports the oven rack so it slides in and out smoothly.
• Prevents racks from sagging, tipping, or binding when pulled forward.
• Restores proper rack alignment to reduce scraping, catching, or loud banging.
• Works with standard oven/range racks that use a molded metal/plastic track system.

• High-level swap: remove the oven racks, unfasten the old track, and secure the replacement in the same mounting locations.
• Use appropriate hand tools and avoid forcing parts; aligning the track before tightening fasteners reduces binding.
• Disconnect power to the appliance or follow the manufacturer's safety guidance if servicing components near electrical connections.