Du84cwdq5 Parts

This channel retainer secures the appliance's front/side panel to the cabinet so panels stay aligned and stable during use. It replaces a worn or broken retainer to reduce panel movement and rattling. What it does:

• Holds the panel channel in place to keep exterior panels aligned
• Prevents panel looseness, shifting, and vibration noise during operation
• Restores proper fit where a cracked or broken retainer allowed gaps
• Works as a direct-fit replacement for the OEM channel retainer

• One channel retainer as shown

• Inspect surrounding clips and screws; replace any damaged fasteners for best fit
• Use basic hand tools; avoid over-tightening fasteners which can crack plastic retainers
• Disconnect power (or unplug) the appliance before accessing panels

Color: White. Size: 13 oz. Spray paint primer. can.

This is the tub funnel seal used to create a watertight connection at the washer tub funnel, helping prevent leaks and keep water flowing to the wash tub where it belongs. It replaces a worn, cracked or flattened seal. What it does:

• Creates a water-tight seal between the tub funnel and surrounding housing to prevent leaks
• Helps keep water directed into the wash tub during fill and drain cycles
• Worn or damaged seals can cause visible water around the top or cabinet and reduced containment
• Replacing a degraded seal restores proper sealing and reduces drip/leak symptoms

• Disconnect power and turn off water supply before starting any repair
• Remove the washer top/agitator or other access panels as required to reach the funnel area
• Inspect mating surfaces and clean away residue before seating the new seal for a proper fit
• Test with a short fill cycle to check for leaks after installation

This disk mount is a small replacement mounting disk that secures and aligns internal components so the appliance operates quietly and reliably. It restores proper fit where a worn or damaged mount causes misalignment or vibration. What it does:

• Provides a secure mounting point for internal assemblies and helps maintain correct component alignment
• Reduces vibration and rattling caused by a broken or deteriorated mount
• Supports stable operation and prevents excess wear on adjoining parts
• Commonly replaced when mount is cracked, warped, or missing

• One disk mount as shown

• Basic hand tools typically required; inspect surrounding components for damage before reassembly
• Disconnect power and/or gas and follow appliance safety procedures before starting work
• Retain all fasteners and observe correct orientation during installation

This door spring provides the tension needed for proper door operation and restores smooth opening and closing. It replaces a worn or broken spring to help the appliance door stay aligned and operate quietly. What it does:

• Supplies tension to the door assembly so the door opens and closes smoothly
• Helps the door stay properly aligned and close securely
• Can prevent sagging or uneven door movement caused by a weakened spring
• Reduces rattling or noisy operation related to a worn door tension spring

• Disconnect power to the appliance before attempting any repair to avoid electrical shock
• Release stored tension carefully; springs can snap back and cause injury—use appropriate tools and eye protection
• Verify correct spring orientation and seating during reassembly to ensure proper door function

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This is a replacement lever latch that secures and releases the appliance door so it closes and opens properly. It restores a worn, broken or cracked lever to help the door latch reliably. What it does:

• Replaces a damaged or worn door latch lever that prevents the door from engaging
• Allows the latch assembly to release so the door can open smoothly
• Common symptom: door won't stay closed, won't latch, or feels loose when closing
• Works as the user-operable lever portion of the door latch mechanism

• Disconnect power (and water if applicable) before servicing the appliance
• Typically snaps or screws into the latch housing—retain fasteners and note orientation
• Inspect latch housing and striker for damage and replace if necessary

This support bearing assembly stabilizes the dryer drum and helps it spin smoothly to improve tumbling and reduce noise. Designed to replace a worn or noisy rear drum support for compatible Whirlpool dryers. What it does:

• Supports the rear of the dryer drum so it rotates evenly
• Reduces squeaks, grinding, and wobbling caused by worn bearings
• Helps maintain proper drum alignment to prevent uneven wear
• Works with the drum shaft to keep tumbling smooth during operation

• One support bearing assembly

• Disconnect power before beginning any repair to avoid electrical shock
• Access may require removing the dryer rear panel and drum; follow manufacturer service instructions
• Inspect adjacent components and replace if excessively worn
• Tighten fasteners to manufacturer torque specs and test operation after reassembly