Du915 Wpq0 Parts

This pump outlet directs drained water from the washer's pump housing into the drain hose, helping the appliance remove wastewater efficiently. Replacing a damaged outlet restores proper drainage and reduces leaks. What it does:

• Channels water from the pump to the drain hose to enable normal draining
• Seals the pump discharge to prevent leaks at the pump exit
• A cracked or clogged outlet can cause slow or no-drain symptoms, leaks under the washer, or water pooling
• Works with the pump assembly to maintain correct water flow during drain cycles

• One pump outlet and the part shown as item 13 in the OEM diagram

• Disconnect power (unplug or switch off breaker) before beginning service
• Turn off and disconnect water lines if needed and place towels to catch residual water
• Inspect and replace any worn clamps, gaskets, or seals when installing the outlet
• Recheck connections and test a short drain cycle after installation to confirm no leaks

This is an electronic console assembly that replaces a damaged or non-working control panel to restore user controls and the display on your appliance. It provides the touch/buttons and electronics needed to select cycles and settings. What it does:

• Houses the electronic control board and user interface (buttons/touchpad and display)
• Replaces damaged or unresponsive controls to restore normal operation
• Addresses symptoms like unresponsive buttons, blank or erratic display, or controls that won't accept selections
• Transfers the appliance's front control functions to a new, pre-assembled unit

• One electronic console assembly

• Disconnect power (unplug or switch off breaker) before beginning any service
• Handle the assembly carefully to avoid damaging ribbon cables, connectors, or the display
• Keep screws and clips organized; some models require removing the cabinet tops or back panels to access mounting points

Color: Black. For white use 3374712. For almond use 3374713

This heater support secures the dryer heater assembly so it stays aligned and stable during operation, helping maintain proper airflow and heating performance. It's a direct-fit replacement designed to restore correct heater positioning. What it does:

• Holds the heater assembly in place to prevent shifting or contact with other components
• Helps maintain proper airflow path for efficient drying and consistent heat
• Reduces rattling, rubbing, or intermittent heating caused by a loose heater
• Works with the heater housing and mounting points to keep electrical and thermal parts separated

• Refer to the dryer's service manual or parts diagram for correct placement and orientation
• Disconnect power before starting work to avoid electrical shock
• Inspect surrounding clips, screws, and the heater assembly; replace any damaged fasteners

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This O-ring is a small rubber replacement seal that helps stop water leaks where two components meet. It restores a tight seal to reduce drips and prevent water damage from worn or cracked seals. What it does:

• Provides a compression seal between mating parts to prevent leaks
• Commonly replaced when visible cracking, flattening, or hardening occurs
• Helps eliminate steady drips or pooling of water near the seal area
• Restores proper sealing after disassembly for service or part replacement

• Disconnect power and shut off the water supply before servicing
• Remove surrounding components carefully to avoid damaging the seal seat
• Inspect the mating surfaces for debris or damage; clean before installing new O-ring
• Lubricate with a compatible, appliance-safe lubricant; do not use petroleum-based products unless specified

This lower spray arm assembly circulates pressurized wash water across the bottom rack to help remove food soil and improve cleaning. It replaces a worn or damaged lower arm to restore proper spray coverage. What it does:

• Directs water flow from the pump to wash dishes on the lower rack.
• Helps maintain even spray pattern and consistent cleaning performance.
• Can prevent poor cleaning or missed spots caused by cracked, clogged, or broken arms.
• Connects to the dishwasher's spray tube or hub to rotate during the wash cycle.

• Disconnect power to the dishwasher before servicing.
• Remove the lower rack to access and remove the old spray arm; typically snaps or unscrews from the hub.
• Inspect the spray arm hub and spray tube connection for debris before installing the new arm.
• Reinstall the lower rack and run a short cycle to verify proper rotation and no obstructions.

This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:

• Rotates and times the dispenser lever/door so the dispenser opens and closes correctly
• Transfers motion from the actuator to the dispenser linkage or switch
• Commonly used when the dispenser lever feels loose, doesn't return, or dispensing is intermittent
• Helps stop unwanted continuous dispensing caused by a worn cam surface

• Disconnect power (and water supply if applicable) before starting work
• Access the dispenser assembly; removal of the dispenser bezel or control housing may be required
• Handle small plastic parts carefully to avoid breaking tabs; align cam on shaft before reassembly
• Test dispenser operation after reassembly to ensure correct movement and sealing