Dws600 Parts

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Agitator screw spacer positions and cushions the agitator screw on top-load washers to keep the agitator stable and reduce wear. It helps maintain correct agitator alignment for reliable wash performance. What it does:

• Centers the agitator and creates the correct spacing for the agitator screw
• Prevents metal-on-metal contact that can cause noise, wear, or loosening
• Helps stop the agitator from wobbling or shifting during the spin cycle
• Contributes to secure engagement between the agitator and the transmission

• Disconnect power to the washer before beginning service
• Remove the agitator per the manufacturer's service instructions to access the screw and spacer
• Install the spacer flat and seated, then reinstall the screw and agitator; follow the OEM service manual for proper fastening procedure
• Inspect the agitator and screw for wear or damage and replace as needed

Wrinkle care on and off switch

This lid strike mounts to the washer lid and engages the lid lock/switch when the lid is closed. It signals the control that the lid is shut so the cycle can start and spin safely without interruption.

• Engages the lid lock/switch to confirm the lid-closed status
• Allows cycles to start and spin once the lid is shut
• Typical failure symptoms: washer won't start or spin; lid won't lock; strike is broken or missing
• Restores reliable lid engagement and safety interlock operation

• Unplug the washer before servicing
• Open the lid and remove the damaged strike from the lid (retain any screws if present)
• Align and secure the new strike; ensure it lines up with the lid lock opening
• Close the lid to verify smooth engagement before restoring power

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

Adjustable

This replacement part is a screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This screw is compatible with many different areas of the appliance. Screws are generally used for keeping parts of the machinery secure and in place during use. It is possible that screws can become loose over time and need to be replaced after years of normal wear and tear.A new screw might be needed if the user notices parts of the appliances are becoming loose or are even falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. The repair for this part is simple. Remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.This screw is sold individually and is a genuine OEM replacement part sourced from the manufacturer.

This exhaust cover plate seals an unused dryer vent opening on the cabinet to prevent air leaks and lint escape. Replacing a missing or damaged cover helps maintain proper airflow and support efficient drying performance. What it does:

• Covers and seals an unused exhaust port on the dryer cabinet
• Helps maintain correct airflow through the exhaust duct
• Helps keep lint and warm, moist air from leaking into the laundry area
• Replace if the original is missing, cracked, loose, or you notice lint/air leakage or longer dry times

• 1 exhaust cover plate

• Disconnect power; for gas dryers, turn off the gas supply
• Locate the unused exhaust opening (rear, side, or bottom—depending on vent configuration)
• Position the plate over the opening and secure using the existing hardware; do not overtighten
• Restore power and verify proper airflow at the active vent

This temperature switch mounts in the dryer control panel and lets you select the desired heat level. Replacing a failed switch restores accurate temperature selection so the dryer responds properly to the setting you choose.

• Selects the heat level for drying cycles
• Routes power through the appropriate heating circuit based on your selection
• Failure symptoms include no change in temperature when turning the knob, being stuck on one heat level, intermittent heat, or a loose/stripped switch shaft
• An internal short or open may contribute to a no-heat condition while the drum still runs

• Disconnect power before servicing; for gas dryers, also shut off the gas supply
• Remove the control knob and open the control console/back cover to access the switch
• Note wire positions; transfer connectors to the new switch one at a time to avoid miswiring
• Mount the new switch securely, reassemble the console, reinstall the knob, and test heat selection

Rear bracket and leveling screw assembly.

This burner assembly is the combustion head for GE gas dryers. It mixes gas and air and directs a stable flame into the heater housing, restoring consistent heat when the original burner is corroded, warped, or clogged.

• Directs the gas flame into the heat chamber for proper drying temperatures
• Works with the igniter, flame sensor, and gas valve to produce heat
• Typical failure symptoms: no heat or intermittent heat, long dry times, burner lights then goes out, unstable/yellow flame
• Physical issues can include rust, warping, or blocked burner ports

• Disconnect power and shut off the gas supply; allow the dryer to cool completely
• Note position of the igniter and flame sensor relative to the burner port; realign during reassembly
• Transfer any reusable fittings from the original burner as needed and verify orifice/fuel type match your installation
• After reconnecting gas, perform a leak check with a non-corrosive soapy water solution before restoring power

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This replacement screw secures panels, trims, and internal components to restore a snug, rattle-free fit and reliable operation. Use it to replace missing, corroded, or stripped fasteners for safe appliance performance. What it does:

• Fastens cabinet panels, trim pieces, and internal brackets to keep parts aligned and secure
• Replaces missing or damaged screws that cause loose or vibrating panels
• Prevents movement that can lead to wear, noise, or improper sealing
• Matches the original fastener role for appliances that specify part WE2M160

• Disconnect power or unplug the appliance before attempting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install until snug; avoid overtightening which can strip threads or crack plastic
• If threads are damaged or fastener holes are worn, replace damaged components.

Package of 12

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.