Efme417siwo Parts

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This thermistor is the temperature-sensing component that feeds accurate readings to the appliance's control. Replacing a faulty sensor restores proper temperature feedback, helping the control run cycles correctly and reduce temperature-related performance issues. What it does:

• Monitors temperature and changes resistance with temperature (NTC), sending a signal to the control board
• Helps the control regulate heating or water-temperature management during operation
• When open/shorted or out of range, can trigger temperature/sensor error codes
• Symptoms include inconsistent temperatures, long run times, or cycles that won't complete

• 1 thermistor

• Disconnect power before servicing; shut off gas/water supply if applicable
• Access the sensor per your model; it's typically secured by a clip or screw and connects via a wire harness
• Note wire orientation; avoid pulling on wires and ensure the connector is fully seated
• After installation, clear any stored error codes and run a diagnostic or test cycle

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

The Lint Screen Cover is an OEM part for Frigidaire dryers. This part secures and protects the lint screen, which captures lint and debris during the drying process. The cover helps ensure that the lint screen fits snugly and operates effectively, preventing lint escape and maintaining optimal airflow within the dryer.

Causes of a bad lint screen cover can include frequent removal and replacement during cleaning, accidental damage, or normal wear and tear from regular use.  

Symptoms of a bad lint screen cover include:

• A loose or ill-fitting cover that can lead to reduced efficiency in trapping lint.
• Visible cracks or damage to the cover, which may impair its function.
• Difficulty in removing or replacing the lint screen due to a faulty cover.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement seal restores a tight barrier between mating surfaces in your appliance, helping contain air, moisture, and heat where intended for reliable performance and efficiency.

• Forms a tight barrier to help prevent leaks, drafts, or heat loss
• Replaces a cracked, torn, flattened, or missing seal
• Can help address issues like moisture around an opening, temperature fluctuations, or rattling/vibration from a poor fit
• Restores proper closure and performance when the original seal is worn

• Disconnect power and shut off water/gas before service
• Note the routing/orientation of the original seal; take photos for reference
• Clean the channel/mating surfaces thoroughly; remove old adhesive and debris
• Seat the new seal fully without stretching; close and test for proper fit and contact

This replacement screw secures appliance panels and internal components. A fresh fastener helps keep assemblies tight and aligned, reducing rattles and vibration so parts stay properly mounted during everyday use.

• Fastens panels, brackets, and assemblies to the appliance frame
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, and loose-fitting components
• Symptoms of a bad/missing screw: loose or noisy panel, component won't stay attached, stripped head/threads

• Disconnect power before servicing; turn off water supply if working on a washer
• Replace one screw at a time to maintain alignment and track locations
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping threads or heads

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.

The Outer Window is an OEM part for Frigidaire dryers. This part provides a clear view into the dryer while it operates. It allows you to monitor your laundry during the drying cycle without opening the door, which helps maintain the efficiency and effectiveness of the dryer by keeping the heat contained.

Causes of a bad outer window can include accidental impacts, general wear and tear, or degradation from the high heat environment inside the dryer. 

Symptoms of a bad outer window include:

• Cracks or breaks in the window that can compromise the insulation of the dryer.
• Scratches or cloudiness that obstruct visibility into the dryer.
• Loose fitting that may affect the door's ability to close properly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Duct Assembly is an OEM part for Frigidaire dryers. This part channels hot air and moisture from the dryer drum to the outside vent. 

Causes of a bad duct assembly can include blockages from lint buildup, physical damage that can restrict airflow, or deterioration over time due to heat and moisture exposure. 

Symptoms of a bad duct assembly include:

• Reduced drying efficiency, with clothes remaining damp after a cycle
• Excessive heat buildup within the dryer
• Unusual noises from the dryer suggesting airflow restriction
• Accumulation of lint within the dryer, indicating poor expulsion of air and debris

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

The Limiter is an OEM part for Frigidaire dryers. It protects the dryer from potential overheating. The limiter is designed to automatically cut power to the dryer's heating elements if temperatures become too high, preventing damage, fires, or other hazardous conditions.

Causes of a bad limiter can include general wear and tear over extended usage, exposure to excessive heat levels, or damage due to manual mishandling or accidental impact.

Symptoms of a bad limiter include:

• The dryer fails to turn off automatically at the end of cycles
• Clothes or interior drum become excessively hot
• Burning smells are detected from the dryer vent
• The dryer cuts out unexpectedly mid-cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Gasket is an OEM part for Frigidaire dryers. This part allows a tight seal around the dryer door, preventing hot air from escaping and cold air from entering during the drying process. 

Causes of a bad door gasket can include normal wear and tear, exposure to extreme temperatures, or accidental damage during loading and unloading of laundry. 

Symptoms of a bad Door Gasket include:

• Clothes taking longer than usual to dry.
• Heat escaping from the edges of the dryer door.
• Visible wear or tears in the gasket material.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.