Eiefw55hiwu Parts

This mounting bracket secures internal components to the appliance chassis, restoring proper alignment and stability. Replaces a broken or bent bracket to stop loose parts, rattling, or misaligned panels for safer, quieter operation. What it does:

• Provides a rigid attachment point for panels, assemblies, or hardware to the cabinet or frame
• Prevents movement that can cause rattling, scraping, or uneven gaps
• Restores correct alignment so related parts operate smoothly
• Helps maintain safe spacing and support for adjacent components

• One mounting bracket as shown

• Disconnect power (and water, if applicable) before installing
• Handle metal edges carefully; wear gloves to avoid cuts
• Use the existing fasteners when possible; replace damaged screws if needed

This replacement bushing is a small sleeve that supports a rotating shaft or drum and helps reduce friction and wear. Restores smoother, quieter rotation for components that contact the shaft or mounting post. What it does

• Supports and centers a rotating shaft or drum to reduce wobble and uneven wear
• Creates a low-friction surface between moving parts to help prevent rubbing and abrasion
• Helps reduce noise caused by metal-on-metal contact
• Commonly replaced when worn, cracked, or causing binding during rotation

• One bushing

• Disconnect power before beginning any repair and follow all safety procedures
• Access and removal vary by appliance model; remove panels or drum as required to reach the worn bushing
• Inspect the mating shaft/post and surrounding parts; replace any damaged components to prevent premature wear
• Use only lubricants and fasteners specified by the manufacturer; do not force parts when installing

This electrical harness is the main wiring assembly that routes power and signals between a fridge's control board and internal components, restoring proper electrical connections for reliable operation. What it does

• Connects the control board to components like lights, fans, sensors, and defrost/heater circuits
• Replaces damaged or corroded wiring that can cause intermittent function or component failures
• Helps resolve symptoms such as no lights, fans not running, intermittent cooling, or error codes related to open/shorted circuits
• Provides factory-style plug connections to maintain correct electrical routing and polarity

• One complete electrical/main wiring harness

• Always disconnect power before servicing electrical components to avoid shock
• Inspect connector pins and wiring for damage; replace harness if any connectors are broken or wires are burnt
• Route harness following existing clips and channels; avoid contact with sharp edges or moving parts

This door seal creates a tight closure around the appliance door to help keep cold air in and warm air out, improving cooling performance and reducing energy use. Replace a worn seal to restore a proper door seal. What it does

• Forms a continuous gasket around the door edge to block air leaks.
• Helps prevent frost build-up and loss of cooling inside the compartment.
• Can reduce cycling and strain on the compressor when the seal is intact.
• Common symptom: noticeable cold-air leakage, frost near the door, or uneven cooling.

• High-level task; remove the old seal by pulling out the retainer and fit the new seal into the door channel.
• Warm the gasket slightly to help seat it evenly; avoid open flames or excessive heat.
• Inspect door frame and retainer for damage before installing the new seal.

This replacement frame restores the appliance's structural trim and alignment to secure panels and components for a snug, finished fit. Use it when the original frame is bent, cracked, or no longer holds parts correctly. What it does:

• Provides structural support and alignment for the appliance's front cabinet or panel
• Helps keep doors and trim properly seated to prevent gaps and rubbing
• Reduces rattling or vibration caused by a loose or damaged frame
• Restores finished appearance where the original frame is dented or broken

• Disconnect power (unplug or shut off breaker) before installing to avoid shock
• Use basic hand tools; some panels or trim may need removing to access mounting points
• Handle edges and fractured plastic/metal carefully to avoid cuts
• Secure all fasteners; check fit before reassembling surrounding parts

This replacement gasket seals the refrigerator/freezer door to help maintain consistent internal temperature and reduce energy loss. A properly sealing gasket improves cooling performance and helps prevent moisture buildup and odors. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in
• Helps prevent frost buildup and water leaks by blocking warm, moist air
• Reduces compressor runtime and energy use caused by escaping cold air
• Common symptom fixes: visible gaps, cold air leak at the door, excess frost, or food spoiling faster than normal

• Disconnect power to the appliance before starting any work.
• Clean the door flange and remove old adhesive or debris for a proper fit.
• Warm the gasket and align the corners, pressing evenly into the channel.
• Check the full seal after installation and allow 24 hours for the gasket to form to the door.