Eif50rd045v Parts

This drive belt turns the dryer drum so clothes tumble for even drying. It replaces a worn or broken belt to restore normal drum rotation and reduce noise or slipping during operation. What it does

• Wraps around the dryer drum and motor/idler to transmit motor torque to the drum
• Restores drum rotation when a worn or broken belt prevents tumbling
• Helps stop squealing, slipping, or burning-smell symptoms caused by a failing belt
• Works with the dryer's idler and motor assembly to maintain proper tension

• One dryer drive belt

• Disconnect power (and gas supply on gas models) before beginning work
• Access may require removing the dryer top/front or rear panel depending on model
• Inspect the idler pulley, drum rollers, and motor shaft while replacing the belt; replace worn supporting parts
• Clean lint and debris from the cabinet and vent path to prevent overheating after repair

This pump assembly replaces the dishwasher drain pump to remove wash water from the tub, helping restore proper draining and prevent standing water after a cycle. What it does

• Pumps wastewater from the dishwasher tub to the drain hose during the drain cycle
• Can resolve symptoms such as standing water in the tub, long drain cycles, or drain-related error codes
• Can reduce grinding or humming noises caused by a failing pump motor or obstructed impeller
• Helps prevent leaks when the pump housing and seals are intact and functioning

• Disconnect power to the appliance before beginning any repair.
• Access typically via the lower front kick panel or by tilting the dishwasher; follow the manufacturer service manual for safe access.
• Inspect and clear any debris from the impeller and hose connections before installing the new pump.

This mounting bracket secures its associated component inside your appliance, keeping it properly positioned during operation. Replacing a bent or broken bracket helps stop rattling or vibration and restores stable, reliable performance.

• Provides a rigid mounting point to the appliance frame or assembly
• Maintains correct position and alignment of the attached component
• Helps reduce vibration and operational noise
• Common failure signs: cracks, bending, stripped holes, or the part no longer stays secured

• Disconnect power before servicing; if working on a washer, also shut off water supply
• Note the original orientation and hardware locations; transfer any clips or grommets from the old bracket
• Reinstall using existing screws and tighten evenly—do not overtighten

The Drain Hose With Push Mount Ties is an OEM part for Frigidaire washing machines. In addition to the drain hose, this kit includes stainless steel push mount ties used to securely fasten the hose in place.

Causes for replacement include standard wear and tear compromising secure hose placement as well as accidental impact that damages existing mounts.

Symptoms of a malfunctioning drain hose installation include:

• Water leaks developing near or under the washer
• Puddles or standing water failure to fully drain
• Loose or jostling hose disconnected from mounts

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door lock secures the appliance door during operation to help prevent accidental opening and ensure cycles run correctly. It replaces a worn or broken latch so the door closes and locks reliably. What it does:

• Physically latches and locks the door to keep it closed during cycles
• Prevents the appliance from starting or running if the door does not engage
• Commonly used when the door will not stay closed or the unit won't begin its cycle
• Helps restore proper door alignment and secure closure when the latch is damaged

• Disconnect power (and water, if applicable) before attempting service
• Basic hand tools typically required; for steps
• Inspect door strike and surrounding trim for damage when replacing the lock

This is a motor-mount screw used to secure the appliance motor housing. It's a direct-fit fastener that restores proper motor attachment to reduce movement and rattling caused by loose or missing hardware. What it does:

• Secures the motor to its mounting bracket or housing
• Prevents motor shifting that can cause vibration, noise, or misalignment
• Restores proper mechanical connection after strip-out or lost hardware
• Helps maintain safe operation by keeping motor fastened

• Disconnect power before servicing the appliance.
• Use the correct screwdriver or socket to avoid stripping the head.
• Thread carefully and tighten to snug; avoid over-tightening which can strip threads.
• If mounting holes or threads are damaged, repair or replace the affected components before reinstalling.

This water inlet valve controls water flow into the refrigerator's dispenser and ice maker so you get reliable filling and ice production. Replaces a worn valve to restore normal water delivery and stop intermittent dispensing. What it does:

• Opens and closes to let water into the ice maker and dispenser when requested
• Prevents water flow when appliances are off or in fill cycle completion
• Common symptom: dispenser or ice maker not filling or producing small/slow amounts of water
• Common symptom: continuous water flow or leaking from valve area

• Turn off power and shut off the water supply before servicing
• Inspect and tighten water line fittings; replace damaged tubing or seals
• Use basic hand tools; verify electrical connectors are secure and undamaged

This replacement drain hose routes and directs waste water away from the appliance to restore normal draining and prevent leaks. Designed to match the original routing and connection points for a direct swap. What it does:

• Carries wastewater from the appliance to the drain system to prevent pooling.
• Replaces cracked, brittle, or clogged hose sections that cause leaks.
• Helps stop intermittent dripping, water under the unit, or slow draining.
• Restores a secure channel for discharge to reduce odor from standing water.

• One replacement drain hose

• Disconnect power and, if applicable, shut off the water supply before starting.
• Place a shallow pan or towels under connections to catch residual water.
• Inspect and reuse OEM clamps only if undamaged; replace corroded clamps with equivalent hardware.
• Push hose fully onto fittings and secure clamps; avoid kinking or sharp bends that restrict flow.

This O-ring is a small rubber seal that helps prevent water or refrigerant leaks by creating a tight connection between mating parts. Replacing a worn O-ring restores a secure seal and reduces dripping or loss of pressure. What it does:

• Forms a leak-tight seal at a joint or fitting to stop drips and seepage
• Helps maintain proper fluid or refrigerant pressure where used
• Commonly replaced when cracked, flattened, or hardened
• Can eliminate intermittent leaks that occur under load or when the appliance cycles

• Turn off and unplug the appliance and shut off water or refrigerant supply before service
• Inspect mating surfaces and replace any damaged fittings to ensure a proper seal
• Lightly lubricate the O-ring with appliance-safe silicone grease; avoid petroleum-based products
• Do not stretch or nick the O-ring during installation; confirm correct seating before restoring power or supply

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install

This is a replacement mounting bracket that secures appliance panels and components, restoring proper alignment and stability. A direct-fit part that helps stop loose panels, rattling, or misalignment for safe, reliable operation. What it does:

• Provides a secure attachment point for panels, trim, or internal components
• Restores correct alignment to reduce rattling and vibration
• Prevents parts from shifting or coming loose during operation
• Re-establishes proper fit where a worn or broken bracket allows gaps

• One mounting bracket

• Install with appliance powered off and disconnected from power source
• Use appropriate fasteners and torque to avoid stripping or damage
• Inspect surrounding clips and hardware; replace any damaged fasteners

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

A replacement tension spring that restores proper return and balance for the appliance component it supports, helping doors and linked mechanisms move smoothly and stay aligned. Designed to match the original fit and function. What it does

• Provides tension to help a door or mechanism return to its rest position
• Restores proper balance and reduces sagging or uneven movement
• Helps eliminate light rattling or inconsistent closing caused by a worn spring
• Works as a direct replacement when the original spring is stretched, broken, or weak

• One replacement tension spring

• Disconnect power and/or unplug the appliance before starting any repair
• Handle spring under tension carefully; wear eye protection and gloves
• Verify the exact spring orientation and anchor points before removal

A simple wire-fastening cable tie that secures wiring and small hoses to prevent rubbing, snagging, or loose routing inside the appliance. Helps keep components organized for safer, quieter operation. What it does

• Secures wiring bundles and small hoses to chassis or brackets to prevent abrasion and movement
• Helps stop intermittent shorts or electrical noise caused by wires rubbing or contacting other parts
• Keeps airflow and moving parts clear by holding wiring away from fans and belts
• Useful when replacing or re-routing harnesses during repairs

• Always disconnect power before working on the appliance.
• Loop tie around wiring or hose, pull to secure snugly, and trim excess tail; do not overtighten.
• Replace ties that are brittle or damaged; use the same routing as the original harness.
• Dispose of trimmed ends and avoid sharp edges that could cut wiring insulation.