Ew301s6cjs Parts

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

This replacement valve controls gas flow to a cooktop/range surface burner, restoring smooth, dependable flame control through the burner knob. Replace a worn or leaking valve to improve safety and consistent burner performance.

• Regulates and shuts off gas to a single surface burner when you turn the control knob
• Helps resolve issues like a burner that won't light or won't adjust flame properly
• Can address a stiff/hard-to-turn knob or gas odor/leak at the valve stem area
• Supports steady, even flame when the original valve is worn or inconsistent

• Disconnect power and shut off gas supply before servicing
• Match the valve to the correct burner position per your model's parts diagram
• Transfer any required fittings/orifice from the original valve
• Use approved sealant where specified and check all connections with a leak-detection solution before use—never an open flame

This electronic oven control board governs bake/broil functions and the front-panel display in your range. Replace it to restore proper heating control and keypad/display operation when the original control has failed. What it does:

• Interprets keypad inputs and oven sensor feedback to switch bake and broil relays
• Regulates oven temperature during preheat and cycling
• Drives the clock, temperature, and status display
• Common symptoms of a bad board: no heat, blank or erratic display, unresponsive buttons, or recurring error codes

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing
• Handle with ESD precautions; avoid touching exposed circuitry
• Note/photograph wire connections; transfer any brackets and the existing overlay if required
• Inspect wiring, oven sensor, elements, and safety cutoffs; correct issues before restoring power and test-baking

This ignitor and orifice assembly provides the ignition source and gas orifice for a gas oven or range burner, restoring reliable ignition for cooking. Replaces a worn or damaged ignitor/orifice to help the burner light correctly. What it does:

• Supplies the ignition element and properly sized orifice so the burner can light and maintain a stable flame.
• Replaces burned-out or cracked ignitors that cause slow or no ignition.
• Replaces clogged or damaged orifices that can cause weak or uneven flames.
• Common symptoms it can address: burner won't light, repeated clicking with no ignition, or a weak/uneven flame.

• Turn off the appliance power and shut off the gas supply before servicing.
• Handle the ignitor carefully—the ceramic/sensing tip is brittle and can break if dropped or bumped.
• Disconnect electrical connectors and note wire positions before removal; reconnect exactly as found.

This radiant surface element restores heat to a smooth-top cooking zone on glass-ceramic ranges. Replace a failed element to bring back consistent, controllable heat for everyday simmering, sautéing, and boiling.

• Provides radiant heat beneath the glass cooktop for one burner zone
• Typical symptoms: burner won't heat, heats only partially, or shows visible hot spots/burn marks
• Helps correct slow-to-heat or uneven cooking performance from a failed element
• Often tests open (no continuity) when the internal coil is burned out

• Disconnect power at the breaker before servicing; elements operate on high voltage
• Lift and support the glass cooktop carefully to avoid cracking the glass
• Note and transfer wires one at a time to the new element; match terminals precisely
• Ensure the element sits level in its brackets and that wires aren't pinched before reassembly

Size: 8-32t x 0.500 inch. Color: Black.

This is the electronic clock/timer that controls the oven. It manages bake and broil functions and provides the display and timing, helping restore proper heating and responsive controls when the original board fails. What it does:

• Controls oven heating by sending power to the bake and broil circuits based on user selections
• Drives the clock, temperature, and status display
• Interfaces with the keypad to run timed baking and other oven functions
• Common failure symptoms can include no display, unresponsive buttons, error codes, or an oven that won't start or heat consistently

• Electronic control board (clock/timer) module

• Disconnect power at the breaker before servicing
• Access the control through the console/control panel; remove mounting screws to reach the board
• Label or photograph wiring and move connectors one at a time to the new board
• Handle by the edges to avoid static damage; secure all mounts and test operation after reassembly

This motor powers the oven's fan to move air through the cavity or chassis, depending on the model. Replacing a weak or failed motor restores proper airflow, helping maintain stable temperatures and protect internal components during cooking and cool-down. What it does and common symptoms:

• Drives the oven's fan for cooling and/or convection airflow
• Fan does not run or starts intermittently
• Loud humming, squealing, or grinding from the fan area
• Control area feels unusually hot or oven struggles to maintain temperature
• Uneven baking performance when using convection (on applicable models)

• One motor

• Disconnect power at the breaker before servicing; allow the oven to cool
• Access is typically from the rear or top; remove panels to reach the motor
• Note wire locations and any rotation markings before removal; transfer any attached fan wheel/bracket as required
• After installation, rotate the fan by hand to check for clearance, then restore power and test operation

Note: ONE screw only, order as needed.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This control mounting hex nut secures the burner or oven control to the control panel, keeping the shaft stable so the knob turns smoothly and the switch stays properly aligned.

• Threads onto the control/infinite switch or thermostat bushing to fasten it to the panel
• Prevents the control from rotating or shifting when the knob is turned
• Replace if the original nut is missing, stripped, rounded, or corroded
• Common signs: loose or wobbly knob, switch spins in the panel, or misaligned knob indexing

• Disconnect power; for gas appliances, also shut off gas before servicing
• Pull off the knob and any trim; support the control body from behind the panel while removing/installing the nut
• Start the new nut by hand to avoid cross-threading; tighten snugly with the correct-size wrench—do not overtighten
• The control sits square in the panel and the knob operates smoothly before restoring power

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

This replacement control knob restores a secure fit and clear setting selection on your range or cooktop. It replaces a worn, cracked, or missing knob so you can adjust heat and functions with confidence. What it does:

• Attaches to the control shaft to select burner or oven settings
• Provides a clear pointer and solid grip for precise adjustments
• Helps ensure safe, reliable shutoff and operation
• Common signs of failure: cracked or stripped insert, loose/wobbly fit, knob falls off, hard to turn, worn-off markings

• 1 control knob

• Disconnect power; shut off gas and allow the appliance to cool
• Pull the old knob straight off the shaft—no tools are typically required
• Align the new knob with the flat (D-shaft) or spline orientation and press firmly until seated
• Rotate through all positions to ensure smooth operation—do not force

This oven light bulb illuminates the interior of your range or wall oven. Replace a burned-out bulb to restore clear visibility while cooking, checking doneness through the window, and cleaning.

• Provides interior illumination when the oven light is activated
• Common fix for no oven light, dim or flickering light, or a failed bulb
• Helps you monitor food without opening the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely to avoid burns
• Remove the lens/cover if present; replace the bulb per your model's socket; do not overtighten
• Restore power and test; if the light still doesn't work, inspect the socket and switch