Fase7073lao Parts

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

Replacement grill trim that restores your appliance's exterior finish and helps direct airflow. Use this grill when the original piece is cracked, missing, loose, or cosmetically damaged to regain a clean, finished appearance. What it does:

• Covers and protects internal components behind the appliance front or vent area.
• Helps direct airflow and reduce drafts around the appliance opening.
• Prevents debris or fingers from contacting internal parts.
• Stops rattling or vibration caused by a bent or loose grill.
• Restores the appliance's original look when the factory grill is damaged.

• Disconnect power at the breaker and allow the appliance to cool before starting any work.
• Remove existing fasteners or clips; retain original screws if they are reusable.
• Align the new grill, then secure with the original hardware; avoid over-tightening to prevent cracking.

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

This electrical wire harness connects key components to deliver power and signal paths so your appliance controls and features operate reliably. It replaces a damaged or worn harness to restore proper electrical connectivity. What it does:

• Routes power and signal between control board, sensors, and accessories
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps resolve symptoms like lights, fans, or controls not powering on or working erratically
• Maintains proper connector fit and wiring color-coding for correct hookups

• One electrical wire harness

• Disconnect power before inspecting or replacing the harness to avoid shock
• Confirm connector orientation and secure all clips; route wiring away from heat and moving parts
• Inspect mating connectors for damage and replace if corroded or burned

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

One per package.

The Steam Hose Kit is an OEM part for Frigidaire dryers. It provides the necessary conduit for steam from the water source to the dryer. The kit includes: 
5’ Rubber Fill Hose with Gooseneck
1’ Rubber Fill Hose (Female/Female)
All Male Y Connector

Causes of a bad steam hose can range from normal wear and tear to improper installation or physical damage from external sources.  

Symptoms of a bad Steam Hose Kit include:

• Leaks or drips from the hose connections.
• Reduced steam output, affecting the dryer's ability to effectively remove wrinkles or sanitize clothes.
• Noticeable wear or damage to the hose, such as cracks or splits.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

This T-plug electrical connector secures a reliable connection between wiring harnesses and appliance components, restoring proper power and signal flow for affected circuits. It's a direct-fit replacement when the plug is damaged or corroded. What it does:

• Provides a secure electrical connection between the harness and the appliance component
• Restores power or signal to components when a broken or loose plug causes intermittent or no operation
• Replaces melted, cracked, or corroded connectors that can cause poor contact
• Helps prevent arcing and further wiring damage when properly seated

• One T-plug electrical connector

• Disconnect power to the appliance before starting any work
• Verify connector orientation and fully seat the T-plug until it clicks or is firmly retained
• Inspect mating harness and terminals for damage or corrosion; replace harness if terminals are compromised
• Use basic hand tools; follow proper electrical and appliance safety practices

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.