Ffbd2412552a Parts

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This factory replacement cover restores a secure, finished shield over the designated area of your appliance. It helps protect internal components and supports proper operation by replacing a cracked, missing, or loose original cover.

• Shields internal parts from dust, moisture, and accidental contact
• Helps maintain intended airflow/splatter control where designed
• Restores proper fit and appearance after damage or wear
• Typical symptoms: cracked, warped, missing, or won't stay attached

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation; transfer any original screws, clips, or seals as required
• Seat tabs and align holes before tightening fasteners
• Do not overtighten to avoid damage; verify clearances before restoring power

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This refrigerator door gasket creates a tight seal around the door to help maintain proper cooling and energy efficiency. It replaces a worn or damaged rubber seal to reduce air leaks and frost buildup. What it does:

• Seals the door perimeter to keep cold air in and warm air out
• Helps prevent frost and moisture buildup inside the compartment
• Supports consistent temperatures for food safety and performance
• Can reduce excessive run time and energy use caused by leaks

• Unplug the appliance or disconnect power before servicing
• Remove the old gasket and clean the gasket channel before installing the new seal
• Warm the gasket slightly if needed to ease installation and ensure proper fit
• After installation, allow time for the gasket to form to the door; check the seal and adjust as needed

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

This console assembly houses the oven/range control interface and display, providing the user-facing buttons, indicators and mounting for your appliance's control electronics. It restores a working control surface and visible status feedback. What it does:

• Replaces the control panel housing, buttons and display area so you can select functions and see oven/range settings
• Restores response when front panel buttons are worn, cracked, or not making contact
• Replaces a console with visible damage, fading, or broken mounting points that affect operation
• Provides the mounting and front bezel for the control electronics and wiring connections

• One console assembly (control panel) as shown

• Disconnect power to the appliance before starting to avoid electrical shock
• Handle the display and button areas carefully to avoid scratching or damaging cosmetic surfaces
• Verify wiring harness connectors and screw locations match your appliance before final installation

This outer refrigerator door replaces a damaged or dented exterior panel to restore your appliance's appearance and proper sealing. It provides a secure barrier for the fresh-food compartment and helps maintain interior temperature control. What it does:

• Replaces a cracked, dented or warped outer refrigerator door panel
• Restores proper door alignment and sealing to help maintain consistent cooling
• Eliminates sharp edges and improves the appliance's appearance
• Works with existing inner liner, gasket, and hinge hardware

• Handle and hinge hardware are often separate; verify you have the correct fasteners before starting
• Lift with help—doors can be heavy or awkward to position
• Disconnect power to avoid risk when removing shelves or electrical components attached to the door
• If the door has trim, gaskets, or handles attached, transfer them carefully or replace with matching parts

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This genuine replacement screw secures appliance panels and components so assemblies stay tight and stable. It's a simple, direct fix when a missing or damaged screw causes loose trim, rattling, or misaligned parts. What it does:

• Fastens panels, brackets, and trim to restore proper alignment and stability
• Stops rattling or vibration caused by loose hardware
• Replaces stripped or corroded screws to ensure secure connections
• Works wherever the OEM screw is specified in the appliance

• Use the matching driver and proper torque to avoid stripping the head or threads
• Replace only with the exact OEM screw to maintain fit and function
• Disconnect power before accessing internal components; follow appliance safety instructions
• Replace all like-for-like for best results

This cup shelf is a direct-fit refrigerator door bin that restores secure storage for cups, bottles and small containers. It replaces a cracked, warped or missing shelf so items stay organized and won't shift on the door. What it does:

• Provides a stable ledge for cups, bottles and small containers on the refrigerator door
• Replaces damaged or cracked door shelving that can no longer support items
• Helps prevent spills and items sliding or falling when the door is opened or closed
• Matches the original shelf shape to maintain proper fit and alignment

• Basic snap-in/screw-in installation; your model's door assembly instructions
• Remove power to the appliance or work with the door empty for safe handling
• Handle carefully to avoid chipping; wear gloves if edges are sharp
• If fasteners are present, reuse original screws/clips or replace with OEM equivalents

This console assembly is the outer housing that holds your appliance's control panel, buttons and display, restoring a clean, secure interface and protecting internal wiring from damage. It provides a factory-fit replacement for worn, cracked or loose control areas. What it does

• Houses and secures the control buttons, knobs and display so controls operate reliably
• Protects internal wiring and electronics from moisture, debris and physical damage
• Keeps the front of the appliance cosmetically finished and aligned
• Replaces cracked, warped or otherwise damaged control panel surfaces that impair use

• One console assembly

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Removal typically requires accessing and removing adjacent trim or the top panel to reach mounting screws and wire connectors
• Support the console while detaching connectors and fasteners to prevent drops or damage