Fffh202qw Parts

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

This replacement door handle restores a damaged or worn refrigerator door grip so the door opens and closes smoothly and looks finished. It matches OEM fit and styling for direct swap replacements. What it does:

• Provides a secure gripping surface for opening and closing the refrigerator door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper door operation when original handle interferes with sealing or use
• Matches original mounting locations for a direct replacement

• Disconnect power to the appliance or unplug the refrigerator before beginning work.
• Remove any trim or access covers to expose handle fasteners; keep small parts organized.
• Use appropriate hand tools; avoid over-tightening fasteners to prevent cracking the handle.

The Fan Mount is an OEM part for Frigidaire refrigerators. It is responsible for holding the evaporator fan in place within the refrigerator's freezer compartment.

A bad fan mount can be caused by regular wear and tear, physical damage, or improper installation. Signs of a faulty fan mount include excessive noise coming from the freezer, reduced cooling performance, or the fan not spinning properly.

Symptoms of a bad fan mount can include:

• Unusual noises coming from the freezer
• Insufficient cooling or uneven temperature
• The evaporator fan not spinning
• Excessive frost or ice buildup in the freezer

Replace your damaged or worn-out fan mount with this genuine OEM part to ensure proper airflow in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This cover protects the appliance's control board and wiring, keeping them secure from spills, dust, and physical damage so the controls work reliably and are easier to service. What it does:

• Shields the control board and associated wiring from moisture, dust, and accidental contact
• Helps prevent shorts and component damage that can cause control or electrical faults
• Keeps wiring and connectors routed and secured to reduce vibration-related issues
• Restores a finished appearance and proper airflow around control components

• One cover as shown

• Disconnect power before servicing to avoid electric shock
• Remove any mounting screws or clips holding the old cover, then lift off and fit the replacement in the same orientation
• Reinstall screws or clips securely but avoid overtightening plastic fasteners

This evaporator coil assembly circulates refrigerant inside the freezer compartment to absorb heat and enable proper cooling. Replacing a faulty coil restores cold temperatures and helps the system run efficiently. What it does:

• Evaporates refrigerant to remove heat from the freezer compartment
• Enables consistent cold airflow for proper food preservation
• Prevents excessive frost buildup when functioning correctly
• Helps reduce long run cycles caused by poor evaporator performance

• 1 evaporator coil assembly

• Disconnect power before starting work and follow basic electrical safety
• Inspect and replace damaged gaskets, insulation, or defrost components as needed for reliable operation
• Test system for leaks and proper cooling after installation

The Freezer Seal is an OEM component specifically designed for Frigidaire refrigerators. This durable rubber seal forms a tight weatherstripping around the perimeter of the refrigerator's freezer door, preventing cold air from escaping. 

Causes of a bad freezer seal include drying out and cracking over many years of use or damage caused by over-tightening the door hinges. 

Symptoms of a bad freezer seal include: 

• Frost or ice buildup around the freezer door seal
• Warm air entering the freezer compartment 
• Higher energy bills due to decreased insulation
• Moisture accumulating in the floor drain 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This condenser coil assembly removes heat from the refrigerant so the refrigerator can cool properly. It's a direct-fit replacement that restores the cooling loop's ability to shed heat and run more efficiently. What it does

• Exchanges heat from the refrigerant to the surrounding air so the cooling cycle can continue
• Helps the compressor run within normal temperature range
• Commonly replaced when the refrigerator is warm inside or the unit runs continuously
• Needed if the condenser is bent, clogged with debris, or leaking

• One condenser

• Disconnect power to the appliance before starting any repair
• Handle with care — coil fins and tubing can be sharp and easily damaged
• Reinstalling may require removal of back or lower access panels; keep fasteners organized
• Sealed-system work (cutting or brazing refrigerant lines) requires certified HVAC service — do not attempt if refrigerant lines must be opened

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

This compressor with mounting clip is the sealed refrigeration compressor assembly that circulates refrigerant to keep your refrigerator cold. Replacing a failed compressor restores the system's ability to cool when repairable. What it does:

• Compresses refrigerant vapor to maintain proper cooling cycle; primary sealed-system pump.
• Commonly linked to symptoms like no cooling, refrigerator runs but temperature rises, or compressor not cycling.
• Works as the sealed-system component; requires correct match to refrigerant and system specifications.

• One compressor assembly with mounting clip as shown.

• Replacement involves sealed-system work.
• Disconnect power before starting; follow all electrical safety practices.
• Use proper tools and gaskets/hoses; pressure-test and leak-check after repair.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement handle restores a secure, comfortable grip so you can open and close your appliance door or drawer with confidence. Replacing a cracked or loose handle improves usability and appearance without affecting the door's alignment.

• Provides the handhold used to open and close the appliance
• Restores operation when the original handle is cracked, broken, loose, or missing
• Helps prevent damage from pulling on trim, frames, or the latch
• Refreshes the look when the old handle is scuffed or discolored

• Unplug or disconnect power before servicing
• Support the door/drawer while removing and installing the handle
• Remove interior/backside mounting screws; transfer original screws, spacers, or caps if required
• Align and tighten screws evenly; do not overtighten