Fflf 3047/Lsb Parts

This small protective cap covers and protects exposed appliance hardware, keeping dirt and moisture out while preventing accidental contact. It's a simple replacement that restores a finished appearance and helps maintain part integrity. What it does:

• Covers and protects an exposed shaft, tab, or fastener from debris and wear
• Helps prevent accidental contact with sharp or moving parts
• Restores the finished look of the appliance where the original cap was lost or damaged
• Simple, passive part—no electrical or mechanical function to reconfigure

• One replacement protective cap

• Always unplug the appliance or disconnect power before servicing
• Remove the damaged cap by hand or with a gentle pry tool; press the replacement into place until fully seated
• Small part—keep away from children and pets; loss is common during disassembly

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

LP orifice / size #84 (5k)

This stainless 30-inch door handle restores a secure, comfortable grip and a clean, factory look to the door. Use it when the original handle is loose, cracked, missing, or cosmetically damaged.

• Replaces a damaged, wobbly, or missing door handle to restore normal opening and closing
• Addresses symptoms like a loose or rattling handle, flexing under pull, or visible wear
• Stainless finish matches the original appearance on compatible units
• Sized to the manufacturer's 30-inch configuration for proper fit

• Disconnect power and allow hot surfaces to cool before servicing
• Support the door; on some models, removing the door provides better access to handle screws
• Transfer any trim/end caps and reuse existing mounting screws per your model's instructions
• Tighten screws evenly; do not overtighten to avoid damaging the door skin or glass

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This wire harness routes electrical power and signals between components to restore reliable operation of the appliance. It replaces a damaged or worn harness to stop intermittent power, control failures, or non-working components. What it does:

• Transfers power and control signals between the appliance control and components
• Restores connectivity when wires are cut, frayed, or connectors are loose
• Helps stop intermittent operation, unresponsive controls, or component power loss
• Provides factory-style connectors and routing for correct fit and function

• Disconnect power (unplug or shut off breaker) before starting any repair
• Match connector shapes and wire colors; route harness along original clips and retainers
• Ensure each connector fully seats and locks; avoid pinching or sharp bends

This operator control panel kit replaces a worn or damaged cooktop/oven control overlay and restores button labeling and user feedback for reliable temperature and function selection. It helps make controls readable and easier to operate. What it does:

• Replaces a cracked, faded, or unresponsive control overlay for the range/oven control area
• Restores clear button and display markings so selections are easier to read
• Helps resolve issues caused by physical damage or wear to the panel surface
• Works with the existing control electronics and mounting points to return a finished appearance

• High-level swap: remove power at the breaker and detach the appliance access panel before replacing the control panel
• Keep fasteners and brackets organized to match original positions during reassembly
• If the control assembly or electronic components are damaged, additional parts may be required
• Follow OEM service manual steps for safe disconnection and reconnection of any wiring

This door trim kit replaces the decorative trim on a refrigerator door to restore a finished look and cover worn or damaged edges. It improves appearance and helps maintain a clean door edge. What it does:

• Replaces worn, cracked, or chipped decorative trim on the refrigerator door
• Covers exposed edges and mounting gaps for a finished appearance
• Restores consistent styling after repair or part replacement
• Helps prevent dirt buildup along the door edge by providing a sealed trim surface

• High-level, drop-in style replacement — no special tools typically required
• Turn off power and empty door area for safe, unobstructed access before starting
• Handle trim carefully to avoid scratching finished surfaces during installation
• Keep original screws/clips and replace any that are missing or damaged

This inner cabinet liner replaces a damaged or worn refrigerator interior surface to restore a clean, sealed cavity and help maintain proper cooling and food protection. Fits the refrigerator fresh-food/freezer compartment where the molded liner is required. What it does:

• Replaces cracked, warped or heavily stained interior cabinet surfaces that can trap dirt or moisture
• Provides a smooth, sealed surface for shelves, drawers and door gaskets to seat properly
• Helps prevent airflow leaks and localized condensation by restoring proper inner cabinet shape
• Common symptom: visible cracks, chips, bubbling, persistent odors or water pooling inside the compartment

• One inner cabinet liner as shown

• Recommended for installers or experienced DIYers; remove power and empty cabinet before starting
• Use appropriate fasteners and sealants specified by manufacturer; avoid over-tightening to prevent cracking
• Inspect surrounding components (shelves, clips, door gaskets) and replace damaged items for best performance
• Follow OEM service manual steps for removal/installation to ensure proper fit and alignment

Color: Black