Ffqe5000qw Parts

This door strike engages the refrigerator/freezer door latch so the door closes and seals reliably. It replaces a worn or broken striker to restore proper door alignment and latching. What it does:

• Provides the mating surface for the door latch to catch and hold the door closed
• Helps maintain a proper seal to prevent cold air loss and reduce frost buildup
• Commonly replaces a cracked, bent, or missing striker that allows the door to pop open
• Can stop issues where the door won't stay closed or the latch can't engage

• Disconnect power to the appliance before starting work to avoid injury
• Remove the door trim or access panel as needed to reach the striker; retain all fasteners
• Align the striker with the latch and tighten mounting screws securely but avoid over-torquing
• Check door swing and gasket seal after installation; adjust strike position if needed for proper latching

This T-plug electrical connector secures a reliable connection between wiring harnesses and appliance components, restoring proper power and signal flow for affected circuits. It's a direct-fit replacement when the plug is damaged or corroded. What it does:

• Provides a secure electrical connection between the harness and the appliance component
• Restores power or signal to components when a broken or loose plug causes intermittent or no operation
• Replaces melted, cracked, or corroded connectors that can cause poor contact
• Helps prevent arcing and further wiring damage when properly seated

• One T-plug electrical connector

• Disconnect power to the appliance before starting any work
• Verify connector orientation and fully seat the T-plug until it clicks or is firmly retained
• Inspect mating harness and terminals for damage or corrosion; replace harness if terminals are compromised
• Use basic hand tools; follow proper electrical and appliance safety practices

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This control panel is the exterior front panel that houses the oven/range controls and provides a finished look while protecting the underlying electronics. It restores a secure mounting surface and normal control access. What it does:

• Provides the user interface area and mounting surface for control buttons, knobs, or touch controls
• Protects internal control electronics from spills, heat, and debris
• Restores a flush, finished appearance when the original panel is cracked, dented, or missing
• Resolves issues where buttons or switches sit unevenly or are difficult to operate due to damaged trim

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Remove adjacent trim and mounting screws to access and replace the panel; handle carefully to avoid scratching or bending
• Keep all original fasteners; replace only parts explicitly required
• If controls or electronic modules are mounted to the panel, verify attachment and wiring connections before restoring power

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This door seal creates a tight closure around the appliance door to help keep cold air in and warm air out, improving cooling performance and reducing energy use. Replace a worn seal to restore a proper door seal. What it does

• Forms a continuous gasket around the door edge to block air leaks.
• Helps prevent frost build-up and loss of cooling inside the compartment.
• Can reduce cycling and strain on the compressor when the seal is intact.
• Common symptom: noticeable cold-air leakage, frost near the door, or uneven cooling.

• High-level task; remove the old seal by pulling out the retainer and fit the new seal into the door channel.
• Warm the gasket slightly to help seat it evenly; avoid open flames or excessive heat.
• Inspect door frame and retainer for damage before installing the new seal.