Ffre1001pwo Parts

Hex washer head ,10-32 x 0.375. Ground

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

This screw is a direct-replacement mounting fastener used to secure appliance panels and internal components, restoring proper fit and reducing vibration or rattling. Simple hardware for repairs that require the correct OEM-style fastener. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Helps stop rattling and vibration caused by loose or missing fasteners
• Matches the original fit and length for reliable reassembly when specified
• Used wherever the appliance's service diagram or manual calls for this screw

• Disconnect power to the appliance before performing service to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head.
• Start threading by hand, then tighten until snug—do not overtighten to prevent stripping or cracking.
• Replace only with the correct OEM part number when diagrams or manuals specify this screw.

This door seal creates a tight closure around the appliance door to help keep cold air in and warm air out, improving cooling performance and reducing energy use. Replace a worn seal to restore a proper door seal. What it does

• Forms a continuous gasket around the door edge to block air leaks.
• Helps prevent frost build-up and loss of cooling inside the compartment.
• Can reduce cycling and strain on the compressor when the seal is intact.
• Common symptom: noticeable cold-air leakage, frost near the door, or uneven cooling.

• High-level task; remove the old seal by pulling out the retainer and fit the new seal into the door channel.
• Warm the gasket slightly to help seat it evenly; avoid open flames or excessive heat.
• Inspect door frame and retainer for damage before installing the new seal.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location