Ffss2315tso Parts

This kickplate grille mounts across the bottom front of the refrigerator. It restores a finished look and helps protect the machine compartment while allowing proper airflow through the condenser area.

• Covers the lower front opening to hide and shield internal components
• Vents air to support proper condenser airflow
• Replaces a damaged, cracked, or missing kickplate
• Common symptoms: broken tabs, grille won't stay attached, visible damage, missing piece

• Disconnect power before servicing
• Open doors to clear the grille; remove the old piece by releasing clips or removing screws
• Align the new grille with the mounting points and snap or fasten into place
• Ensure the grille sits evenly and doesn't interfere with door swing or airflow

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

The Wiring Harness is an OEM part for Frigidaire refrigerators. As the complex network distributes power throughout the cabinet, this harness is crucial for seamless communication between electrical parts. Its bundled cables provide synchronized functioning of all refrigerator operations.

Symptoms of a faulty wiring harness can include:

• Lights, fans, or features randomly activating or shutting off
• Door open or cooling light failure despite replacement of lightbulbs 
• Intermittent buzzing, humming, or crackling sounds from wires
• Water leaks or blown fuses due to short circuits from damaged insulation

Causes involve normal insulation breakdown from years of vibration, heat cycling, and flexing stress. Rodent damage or pinched/cut wires may also disrupt circuits.

Replace it with this genuine Frigidaire harness to restore a consolidated and durable part, avoiding further diagnostics and piecemeal replacements down the line. Compatible with some Electrolux, Gibson, and Kenmore models.
 

The Handle is an OEM part for Frigidaire refrigerators. This part is responsible for providing a secure grip and facilitating the opening and closing of the refrigerator door.  

Causes of a damaged or ineffective refrigerator door handle can include normal wear and tear from daily use, accidental impacts that result in cracks or breaks, and loosening of the handle's fittings over time. 

Symptoms of a bad refrigerator door handle include:

• Difficulty in opening or closing the refrigerator door.
• A loose handle that moves or wobbles when touched.
• Visible damage, such as cracks or breaks, that can also pose safety risks.
• The handle detaching from the door, requiring immediate replacement for proper operation.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This control rod spring fits the refrigerator's ice maker shutoff arm. It restores proper tension so the ice maker cycles on/off correctly and stops making ice when the bucket is full.

• Maintains tension on the ice maker control/shutoff arm for reliable on/off operation
• Helps the arm return to position so the ice maker senses a full bin and pauses production
• A weakened or missing spring may cause an overfilling ice bucket, a loose arm, or inconsistent ice production
• Replaces damaged or stretched springs that prevent the control rod from moving smoothly

• Unplug the refrigerator and shut off water to the ice maker
• Empty the ice bin and access the shutoff arm pivot
• Note the spring's orientation; install with needle-nose pliers without bending the control rod
• Restore power/water and verify smooth arm movement and proper shutoff

This lower hinge bracket mounts at the bottom of the cabinet to support and align the refrigerator door. Replacing a bent or worn bracket helps restore smooth door operation and a consistent gasket seal to help reduce air leaks.

• Provides the mounting base for the lower hinge/pin at the bottom of the cabinet
• Supports the door's weight to keep it level and properly aligned
• Helps the door open and close smoothly without scraping or binding
• Typical symptoms: door sagging or misalignment, difficulty closing, gaps at the gasket, squeaks/scraping near the lower hinge, or visible bracket damage

• Disconnect power; remove items from the door and support the door to prevent dropping
• Mark hinge/bracket locations for alignment; remove bottom hinge cover and mounting screws
• Transfer hinge pin and any spacers from the old bracket if applicable; install the new bracket and tighten screws securely
• Rehang and align the door; confirm full gasket contact and smooth door swing

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

The Handle is an OEM part for Frigidaire refrigerators. This part allows for easy access to your refrigerated goods. The sleek design ensures that it not only functions well but also complements the aesthetic of the appliance, fitting seamlessly with the refrigerator's exterior.

Causes of a damaged or ineffective refrigerator door handle can include normal wear and tear from daily use, accidental impacts that result in cracks or breaks, and loosening of the handle's fittings over time.

Symptoms of a bad refrigerator door handle include:

• Difficulty in opening or closing the refrigerator door.
• A loose handle that moves or wobbles when touched.
• Visible damage, such as cracks or breaks, that can also pose safety risks.
• The handle detaching from the door, requiring immediate replacement for proper operation.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

Black

Front plate restores the appliance's front-facing cabinet, protecting internal components and improving appearance. It replaces cracked, dented or worn front trim so the appliance looks finished and covers internal parts. What it does:

• Covers and protects internal components behind the appliance's front cabinet.
• Restores cosmetic appearance when the existing front is dented, cracked, or scratched.
• Helps maintain proper fit and alignment of adjacent trim and access points.
• Reduces exposure of internal components to dust and incidental contact.

• Always disconnect power (and water, if applicable) before beginning work.
• Removal typically requires removing fasteners, clips or adjacent trim panels—keep track of all screws.
• Handle carefully; edges may be sharp and panels can be awkward to position alone.

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.