Fftr1814qwa4a Parts

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This electronic control box is the main control board that manages refrigerator functions and timing. It replaces a failed control module to restore normal operation of the unit's control logic and cycles. What it does:

• Regulates refrigerator control functions such as defrost cycles, compressor and fan commands, and user-interface signals.
• Replaces a faulty control module that causes no cooling, intermittent operation, or unresponsive controls.
• Helps clear control-related error codes when the board itself is the confirmed cause.
• Interfaces with temperature sensors and other system components to maintain normal appliance behavior.

What's included: One control box (single electronic control board) Install notes:

• Disconnect power to the appliance before attempting any service to avoid electric shock.
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available.
• Verify the part number on the existing board matches this replacement before installing.

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

Color: Black. Rubber. Holds tube/wire

This compressor kit replaces the start components that help the compressor kick on, restoring reliable cooling and reducing hard-start symptoms. Fits refrigerators that use a separate start device and overload protector on the compressor. What it does:

• Provides the compressor start device and overload protector that help the compressor motor start and protect it from overheating.
• Restores normal compressor startup when the refrigerator hums but won't start or cycles irregularly.
• Helps stop repeated clicking or short-run cycles caused by failed start components.
• Works with compressors that require an external start relay and thermal overload for proper operation.

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Handle components carefully and install in the correct orientation on the compressor terminals per manufacturer wiring.

A molded gasket that seals the evaporator coil cover to reduce air bypass and help direct cold air over the coils for more consistent cooling. Replaces a worn or damaged seal to help restore proper airflow and reduce frost buildup. What it does:

• Seals the evaporator coil cover to prevent warm air from bypassing the coil
• Helps maintain proper airflow for consistent cooling performance
• Reduces frost or ice buildup caused by air leaks around the coil cover
• Prevents condensation and dripping by keeping air where it belongs

• Disconnect power to the appliance before servicing to avoid electrical shock
• Thaw any frost/ice accumulation and remove the evaporator access cover per manufacturer instructions
• Clean mating surfaces, then press the seal into place ensuring a full, even fit around the cover

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and warm air out, preserving food freshness and helping the appliance run efficiently. What it does:

• Seals the door to maintain proper internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps reduce compressor runtime caused by air leaks
• Restores a tight magnetic seal for reliable door closure

• Disconnect power before starting any repair.
• Remove the old gasket and clean the gasket channel; install new gasket, aligning the magnetic edge and corners.
• Check for full compression around the door; adjust or reseat as needed for an even seal.
• Allow the gasket to settle and recheck after 24 hours; avoid using sharp tools that could damage the seal.

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This control box housing protects and secures the range/dryer/washer electronic control assembly, keeping wiring and the control board mounted and shielded from debris and heat. It restores a stable enclosure for reliable control operation. What it does:

• Provides a mounting enclosure for the appliance electronic control board and associated wiring harnesses
• Shields circuits from dust, moisture and incidental contact that can cause shorts or intermittent operation
• Keeps control components properly aligned so knobs, switches or displays sit correctly
• Helps prevent vibration-related loosening or damage to the control assembly
• Can eliminate symptoms like loose or rattling controls, exposed wiring, or intermittent control behavior when the housing is broken

• Disconnect power (unplug or turn off breaker) before any service to avoid shock or damage
• Handle the control board and ribbon cables carefully; transfer the PCB and fasteners from the old housing to the new housing if required
• Use the manufacturer-recommended screws/fasteners and correct alignment before restoring power

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head