Ffv21f5hwb Parts

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

This replacement screw secures appliance panels and components to restore proper fit and reduce vibration. Use when original fasteners are lost, stripped, or damaged to keep parts aligned and prevent noise or movement. What it does:

• Fastens trim, panels, brackets or small components to maintain proper alignment
• Helps stop rattling, vibration, or loose parts caused by missing or worn screws
• Replaces stripped or corroded screws to restore secure connections
• Matches the original mounting function for reliable holding strength when correctly installed

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and hand-start screws to prevent cross-threading; tighten securely but avoid over-torquing
• If threads in the mating part are damaged, inspect and repair or replace the mating part rather than over-driving a screw

This hanger secures the hanging basket to the appliance rack so the basket stays in place during normal use. It replaces a broken or bent hanger to restore proper basket support and alignment. What it does:

• Holds the hanging basket on the rack to prevent sagging or detachment
• Restores stable basket movement and alignment when loading or unloading
• Helps eliminate rattling or shifting caused by damaged hangers
• Matches the OEM mounting points for a direct-replacement fit when installed correctly

• Turn off and unplug the appliance (or shut off power) before starting any repair.
• Remove the basket and any obstructions to access the hanger mounting location.
• Compare the new hanger to the old part for correct orientation before fastening.
• Use basic hand tools; replace any worn fasteners and test basket support after reassembly.

This hanging basket hanger is a support bracket that secures a wire storage basket inside the appliance, restoring stable basket positioning and smooth operation. Durable replacement for worn or broken basket supports. What it does:

• Supports and locks a hanging wire basket into place so it stays level and secure.
• Prevents baskets from slipping, tilting, or falling when loading or removing items.
• Restores proper alignment for smooth insertion and removal of the basket.
• Helps eliminate rattling or banging caused by a loose or damaged hanger.

• Designed for simple replacement; remove the basket to access the hanger mounting points.
• Use basic hand tools; avoid forcing parts to prevent damage to surrounding trim or liners.
• Disconnect power only if installation requires reaching electrical components; otherwise follow normal safety precautions.
• Inspect mating clips and basket edges for damage and replace if necessary for proper fit.

This compressor with mounting clip is the sealed refrigeration compressor assembly that circulates refrigerant to keep your refrigerator cold. Replacing a failed compressor restores the system's ability to cool when repairable. What it does:

• Compresses refrigerant vapor to maintain proper cooling cycle; primary sealed-system pump.
• Commonly linked to symptoms like no cooling, refrigerator runs but temperature rises, or compressor not cycling.
• Works as the sealed-system component; requires correct match to refrigerant and system specifications.

• One compressor assembly with mounting clip as shown.

• Replacement involves sealed-system work.
• Disconnect power before starting; follow all electrical safety practices.
• Use proper tools and gaskets/hoses; pressure-test and leak-check after repair.

Restore proper auto-defrost performance in your refrigerator. This defrost heater assembly melts frost off the evaporator during defrost cycles, and the included thermostat helps end the cycle at the correct temperature to prevent over-defrosting.

• Heats the evaporator to clear built-up frost and maintain airflow
• Thermostat monitors coil temperature to terminate defrost at the right time
• Common failure signs: heavy frost/ice on the evaporator, poor cooling, warm fridge but cold freezer, or frequent icing after defrost
• Helps reduce noisy fan icing and improves temperature stability

• Disconnect power before service; components get hot during and after use
• Access is typically from the freezer section behind the evaporator cover
• Note wire routing and clip locations before removal; transfer thermostat to the same position if applicable
• After installation, verify heater and thermostat connections are secure and unobstructed

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement handle restores a secure, comfortable grip so you can open and close your appliance door or drawer with confidence. Replacing a cracked or loose handle improves usability and appearance without affecting the door's alignment.

• Provides the handhold used to open and close the appliance
• Restores operation when the original handle is cracked, broken, loose, or missing
• Helps prevent damage from pulling on trim, frames, or the latch
• Refreshes the look when the old handle is scuffed or discolored

• Unplug or disconnect power before servicing
• Support the door/drawer while removing and installing the handle
• Remove interior/backside mounting screws; transfer original screws, spacers, or caps if required
• Align and tighten screws evenly; do not overtighten

This shim is a small alignment spacer used to correct fit, spacing, or leveling between appliance components for improved part clearance and smoother operation. It helps restore proper alignment and reduce rubbing or binding where parts meet. What it does:

• Provides a thin, stable spacer to adjust panel, door, or component alignment
• Helps eliminate rubbing, binding, or misaligned gaps that cause noise or wear
• Restores proper clearance so moving parts operate smoothly
• Useful when replacing or reassembling components to achieve correct fit

• Shim

• Turn off and unplug the appliance before starting any work
• Inspect surrounding parts to ensure the shim addresses the alignment issue
• Position the shim between mating surfaces as needed; secure per OEM guidance

This dishwasher silverware basket organizes and secures flatware and small utensils for thorough cleaning. It replaces a cracked, warped, or missing basket to help prevent pieces from slipping through or obstructing the spray arm. What it does:

• Holds forks, spoons, knives, and small utensils during wash cycles
• Keeps items upright and separated for better spray coverage and drying
• Helps prevent small pieces from falling through or blocking the spray arm
• Replace if cracked, broken, or if utensils tip over or slide out

• 1 silverware basket

• Open the dishwasher and remove the old basket from the rack; set the new basket in the designated position
• Ensure the basket does not interfere with rack movement or spray-arm rotation
• Load sharp items with points down

This small mounting clip secures interior or cabinet components to keep panels and trim stable, helping reduce noise and maintain proper alignment. It's a simple replacement that restores a snug fit where the original clip has broken or worn. What it does:

• Holds panels, trim, or small components in place to prevent gaps or rattling
• Restores proper alignment of clipped parts after damage or wear
• Maintains a secure attachment point for adjacent parts during normal use
• Helps prevent moisture or debris from entering behind secured panels

• Disconnect power or unplug the appliance before accessing internal components
• Handle the clip and surrounding trim carefully to avoid cracking adjacent plastic
• Use basic hand tools as needed; do not force clips into place—align before snapping
• Replace any damaged mounting features for a secure fit

This wire oven rack provides a sturdy platform for cookware and bakeware, restoring proper support and airflow inside the oven for even cooking. It fits in compatible Frigidaire/Whirlpool-style ranges and drop-in ovens. What it does:

• Supports pans, baking sheets and cookware securely during baking or roasting
• Helps maintain proper air circulation for consistent oven temperatures
• Replaces bent, warped or missing racks that cause unstable cookware
• Restores rack position options for broiling, baking and roasting

• One wire oven rack

• Slide rack into oven grooves until it seats; no tools required for most installs
• Allow oven to cool completely before installing or removing the rack
• Handle with care—edges may be sharp and the rack can be heavy when loaded
• Clean with nonabrasive cleaners; follow oven manufacturer cleaning recommendations