Fgdh2465nf1a Parts

This transformer supplies the low-voltage power needed by an appliance's control system so the user interface and control board operate correctly. Replaces a worn or failed transformer to restore proper control voltage and reliable operation. What it does:

• Converts incoming line voltage to the lower control voltage used by the appliance's control board and display.
• Common symptom: control panel or display is dim, blank, or intermittently responsive.
• Common symptom: control functions (timers, cycles, lights) fail or reset unexpectedly.
• Helps stabilize control voltage to prevent erratic electronic behavior.

• One transformer

• Disconnect all power (unplug or shut off breaker) before accessing internal components.
• Observe proper wiring and polarity; match connections to the original transformer and secure terminal fasteners.
• Use appropriate mounting hardware and strain reliefs; avoid pinching or exposing wires.

This rubber bumper cushions doors and panels to reduce noise, prevent metal-on-metal contact, and protect finishes for smoother, quieter operation. Replace worn or missing bumpers to help restore proper seating and reduce rattling. What it does:

• Absorbs shock between moving parts to prevent bangs and scratches
• Keeps doors and panels aligned for a tighter seal and quieter close
• Reduces vibration and rattling during operation
• Helps protect painted or plated surfaces from wear at contact points

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Typically a push-in or snap-in replacement; press into the original mounting hole until seated
• Inspect nearby bumpers and replace in matched sets if others are cracked or missing

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

Specs: 8 - 18 x 0.500

The Spark Ignition Switch and Harness is an OEM part for Frigidaire gas ranges. It houses the electronics and wiring that control pilot light ignition on the oven/broiler burner.

Causes of a faulty unit involve typical degradation of switch contacts from accumulated heat cycles. Insulation breakdown over time from constant flexing of the coil harness is also common. 

Symptoms include:

• Inability to light or sustain the oven pilot flame
• Intermittent or no response from control knob 
• Erratic ignition at the pilot or thermocouple
• Peeling/frayed outer casing on wiring segments

This OEM replacement is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This control panel is the front console fascia that houses the oven/range controls and display, restoring the unit's user interface and appearance. It replaces a cracked, faded, or damaged console face to make controls accessible and look like new. What it does:

• Provides the visible bezel and button/display surface for the unit's electronic controls
• Restores a secure mounting surface for control buttons, knobs, and display elements
• Helps resolve issues with broken, cracked, or cosmetically damaged console areas
• Supports proper alignment of control electronics

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Basic disassembly (removing trim screws and console fasteners) is typically required; keep hardware for reassembly
• Handle carefully to avoid scratching or cracking the new panel during install
• If control electronics or trim pieces are damaged, verify those parts separately; this panel is the fascia only

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This replacement control knob restores reliable user control for a range or cooktop. It provides a secure, easy-to-grip interface to turn settings and replace a missing, cracked, or worn knob. What it does:

• Replaces a broken, cracked, stripped, or missing control knob so you can adjust settings again
• Provides a firm grip for smooth turning and accurate selection of heat or function
• Helps prevent accidental changes caused by a damaged or loose knob
• Matches OEM fit and appearance for straightforward replacement

• Disconnect power to the appliance before servicing to prevent shock or injury
• Pull the old knob straight off the shaft (no special tools typically required); align and push the new knob on until fully seated
• If the knob is tight or stuck, your model's service instructions before using tools to avoid shaft damage
• Proper operation after installation; do not force the knob if it does not fit

This mounting bracket secures internal components to the appliance cabinet, restoring proper alignment and stable support where factory brackets have broken or come loose. A direct-fit replacement that helps stop shifting, rattles, and misalignment. What it does:

• Provides a secure mounting point for panels, assemblies, or components inside the cabinet
• Restores correct alignment when a damaged bracket allows parts to sag or move
• Reduces vibration and rattling caused by loose or missing support
• Helps maintain proper clearances for doors and internal assemblies

• One replacement mounting bracket

• Disconnect power to the appliance before starting any repair
• Remove any obstructing panels, shelves, or components to access the bracket
• Keep original fasteners; replace only if explicitly specified by OEM instructions

This is a burner grate for stoves and ranges. It sits on top of the burner head and acts as protection for that part. It's made of durable metal to handle the high temperatures of the stove and the weight of large pots and pans. Burner grates are wider than the burner and create a more stable area for cooking needs. There are several situations where one or more burner grates need to be replaced. The parts may become rusty, cracked, or broken and are no longer appropriate for use.Before the replacement, unplug the stove and make sure any utilities are disconnected from the appliance. The stove should be cool to the touch before starting. This is an easy replacement process that doesn't necessitate tools. However, a pair of work gloves will be useful. Access the burner grate that is cracked or broken and grasp it with the hands. Pull the broken grate off of the range. Use the new burner grate to replace it.This is a genuine OEM replacement part that is compatible with Frigidaire ranges and stoves. It comes directly from the manufacturer and is priced as a single unit.