Fghb2866pa Parts

This factory screw secures components inside your refrigerator. Replacing a missing, rusted, or stripped fastener restores a tight, rattle-free fit for shelves, panels, and brackets so everything stays aligned, supported, and quiet.

• Fastens panels, brackets, or trim to the cabinet/liner
• Replaces damaged, corroded, or stripped hardware
• Helps resolve looseness, vibration, rattling, or misalignment
• Maintains proper support for shelves, covers, and assemblies

• Unplug the appliance; if working near water lines, shut off the water supply
• Match the new screw to the original; transfer any washers or spacers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving clip/insert is damaged, replace it to ensure a secure repair

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water fill chute kit channels incoming water from the fill tube into the ice maker mold. Replacing a cracked or deformed chute helps stop leaks and ice buildup at the fill area and supports consistent, properly directed fills for reliable ice production.

• Directs water from the inlet/fill tube into the ice maker mold during the fill cycle
• Helps prevent splashing, leaks, and ice accumulation at the fill point
• Replaces damaged, warped, or missing chute/funnel components
• Typical symptoms: water dripping near the ice maker, frost/ice around the fill area, cubes clumping together, intermittent ice production

• Disconnect power and shut off the household water supply before servicing
• Remove the ice bin and access the fill area at the rear/top of the ice maker
• Clear any ice blockage; remove fasteners/clips to take out the old chute; transfer any seals or grommets if present
• Align the new chute with the fill tube and mold, seat fully, secure, then restore water/power and run a test fill to check for leaks

This mullion guide secures and aligns the refrigerator's vertical door trim so doors close evenly and seals engage properly. Replacing a worn or broken guide helps restore door alignment and reduce drafts at the center seam. What it does:

• Holds the mullion/vertical trim in place and keeps the trim flush with the cabinet
• Guides the doors during closing to maintain even gaps and seal contact
• Prevents the mullion from shifting, rattling, or catching when doors open or close
• Common symptom: loose, misaligned, or damaged center trim causing wind, noise, or uneven door gaps

• Disconnect power before starting service and work on a stable surface
• Remove the mullion/trim and any surrounding gaskets or screws as needed to access the guide
• Use appropriate trim/removal tools to avoid damaging adjacent plastic or gasket material
• Reinstall hardware securely and verify doors close and seals engage properly after installation

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This slide assembly restores smooth, stable movement to your refrigerator drawer or basket so it opens and closes easily and stays aligned. Replace a worn or cracked slide to eliminate sticking, sagging, or track problems.

• Guides and supports the drawer/basket along the cabinet track
• Maintains alignment to prevent binding, rubbing, or popping off the rail
• Restores full, smooth travel for easier access to contents
• Common symptoms: drawer hard to open/close, sits crooked, falls off track, or makes scraping/clicking noises

• Disconnect power and remove the drawer and contents before starting.
• Note the slide's orientation; remove mounting screws/clips and the old slide.
• Install the new slide in the same position; transfer any snap-on brackets from the original if applicable.
• Reinstall the drawer, ensuring both sides are seated on the tracks, and test for smooth operation.

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

This bushing is a small bearing insert that supports a pin or shaft within an appliance mechanism. Replacing a worn bushing restores smooth movement and helps prevent accelerated wear, scraping, and noise in the affected assembly.

• Provides a low-friction surface for pivoting or sliding components
• Helps correct loose, wobbly, or uneven movement
• Can reduce squeaking, scraping, or binding during operation
• Replaces cracked, distorted, or missing bushings to maintain alignment

• Disconnect power and, if applicable, shut off the water supply before servicing
• Note the original bushing's orientation and depth; seat the replacement fully in the same position
• Inspect the mating pin/shaft and surrounding bracket/hinge for wear; replace any damaged parts
• Do not overtighten fasteners through plastic and avoid lubricants unless specified by the manufacturer

Color: Stainless Steel
The Dispenser Trim is an OEM part for Frigidaire refrigerators. It surrounds the ice and water dispenser area located externally on the refrigerator door.

Causes of a faulty dispenser trim can include cracks, chips or damage from impacts or general wear over time.

Symptoms of failure include:

• Water leaks developing around the dispenser opening
• Loose or detached trim that does not sit flush
• Access to dispenser functions being obstructed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This upper hinge cover fits the left-hand side and snaps over the top door hinge in a gray finish. It protects the hinge hardware and restores a clean, finished look when the original cover is cracked or missing.

• Conceals upper hinge hardware on the left side for a clean appearance
• Shields the hinge area from dust and minor spills
• Helps prevent snagging or damage to wires routed through the hinge area on some models
• Typical symptoms: broken, loose, or missing hinge cover

• Disconnect power to the appliance before servicing
• Remove any retaining screw(s) or release tabs from the old cover; keep original fasteners for reuse
• Align the new cover over the hinge and snap or secure into place
• Support the door before loosening fasteners

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bar is a direct-fit support component that helps hold and stabilize a refrigerator door or interior shelf assembly, restoring secure storage and preventing items from shifting or falling. What it does

• Provides structural support for a door or shelf ledge to keep stored items secure
• Replaces bent, cracked or broken bars that allow shelves or door bins to sag
• Helps stop rattling or movement from loose or damaged supports
• Restores proper alignment so shelves and bins sit flush and stable

• One replacement bar

• Disconnect power before removing refrigerator doors or interior components when necessary
• Remove affected shelf or bin to access mounting points
• Use basic hand tools; avoid overtightening fasteners to prevent cracking plastic parts
• Handle glass shelves and door bins carefully during removal and reassembly

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

The Slide Assembly is an essential OEM component for Frigidaire refrigerator drawers. It provides smooth extension and retraction of covered storage bins during access.  

Symptoms of a faulty slide assembly include:

• Squeaking or rubbing noises coming from drawer rails   
• Difficulty smoothly pulling out covered bins
• Scratches or gouges visible along wear surfaces

Causes involve years of constant sliding stresses overwhelming lubrication, leading to increased friction. Without smooth gliding, premature deterioration of plastic drawer supports results.

This authentic OEM replacement is compatible with Frigidaire, Electrolux, and Kenmore models.

This electronic power control board manages incoming power and directs it to the refrigerator's compressor, fans, and control circuits. Replacing a failed board can help restore cooling performance and bring unresponsive or intermittently running units back to normal operation.

• Distributes and regulates power for the compressor and fan motors; failure can leave the unit warm or silent
• Sequences cooling operations based on sensor/control inputs; faults may cause intermittent starting or frequent power cycling
• Interfaces with the refrigerator's controls to execute cooling commands; issues can present as an unresponsive control panel
• Contains relays and protective circuitry; burn marks or repeated relay clicking can indicate a defective board

• Disconnect power before service; use anti-static (ESD) precautions when handling the board
• Board is typically located at the back of the refrigerator in the machine compartment behind the rear access panel
• Photograph wiring; move connectors and any jumpers to the new board, matching positions and orientation
• Ensure all plugs are fully seated, reassemble, restore power, and allow up to 24 hours for temperatures to stabilize