Fghb2866pa Parts

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement retainer clip secures trim, panels or small components inside your appliance to restore proper fit and reduce rattling. A simple, low-cost part commonly used where plastic or metal pieces need a secure hold. What it does:

• Holds panels, trim pieces or small assemblies in place to prevent shifting and vibration.
• Helps stop rattling, loose trim or components that don't stay seated.
• Keeps wiring or hoses routed and restrained when used as a harness/route clip.
• Suitable when original clip is cracked, broken or missing.

• Disconnect power to the appliance before beginning any work.
• Remove surrounding trim or panels gently to access the clip location; a trim tool or small screwdriver may be helpful.
• Clip installs by pressing into the mating slot or hole until it snaps; pliers may assist for removal/replacement.
• Verify correct orientation and fit by comparing the new clip to the old one before final reassembly.

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

This refrigerator housing is the molded support used to mount and protect its associated components inside the appliance. Replacing a damaged housing restores a secure fit and proper alignment so parts stay in place and function correctly.

• Provides structural support and mounting points for the related controls/components
• Helps route air and/or wiring as designed by the manufacturer
• Restores proper alignment to reduce rattles, rubbing, or interference
• Symptoms can include cracked plastic, broken tabs, loose or sagging assemblies, or components that won't stay secured

• Disconnect power before servicing; shut off water as needed if working near dispenser/ice components
• Transfer sensors, wiring, controls, and hardware from the original housing unless new parts are supplied
• Reuse original screws/clips; avoid overtightening to prevent cracking
• Verify harness connections and clearances before restoring power and water

This replacement water tank stores and supplies fresh water to the refrigerator's dispenser and ice maker, restoring proper water delivery and reducing leaks or slow/irregular filling. Designed to match the original fit and function. What it does:

• Holds the refrigerator's fresh water supply used by dispenser and ice maker
• Replaces a cracked, leaking, or otherwise damaged reservoir
• Helps restore normal dispenser flow and consistent ice production
• Prevents water pooling or internal leaks from a compromised tank

• Disconnect power and shut off the water supply before beginning work
• Remove interior panels and trim carefully to access and replace the tank
• Handle the tank gently to avoid damage to mounting tabs and fittings
• After installation, turn on water, check all connections, and inspect for leaks

The Slide Assembly is an OEM part for Frigidaire refrigerators. It secures crisper and pantry bins within the refrigerator interior, providing gliding functionality for easy access to stored items.

Causes of a bad slide assembly can include loose or broken mounting features, damaged rollers, or bent metal rails failing to guide bins smoothly. 

Symptoms of a bad slide assembly include:

• Difficulty removing or replacing crisper/pantry bins  
• Bins failing to close fully or stay securely in place
• Loud squeaking or grinding noises developing
• Dislodged mounting screws or loose mounting points

Replacing with this OEM slide assembly restores smooth operation. It is purpose-built to support everyday use without degradation.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before further component wear develops.

Note: Optional Freezer Ice Maker (2nd IM) for French Door Bottom Mount Standard-Depth models.

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves

This replacement door handle restores a sturdy, comfortable grip on your refrigerator door. It replaces cracked or loose handles so you can open and close the door safely while keeping the appliance's appearance clean and finished.

• Provides the leverage and grip needed to open and close the door
• Restores appearance when the original handle is worn, discolored, or broken
• Helps prevent stress on the door gasket by giving a proper grab point
• Common signs of failure: handle is cracked, loose, wobbly, or missing

• Disconnect power before servicing; turn off water supply if working near a dispenser line
• Open the door and remove any decorative end caps to access the mounting screws
• Support the handle, remove screws, position the new handle, and reinstall using existing hardware; do not overtighten
• The handle is secure and the door opens and closes smoothly

Replacement water tube that carries water from the inlet valve to the dispenser and ice system, restoring water delivery and preventing leaks when the original tube is cracked, clogged, or disconnected. What it does:

• Routes water from the refrigerator inlet valve to the ice maker and/or water dispenser.
• Restores normal water flow when the existing tube is blocked, kinked, or leaking.
• Helps stop leaks and puddling caused by cracked or damaged tubing.
• Matches original routing and connections to maintain proper water delivery.

• Disconnect power and shut off the refrigerator water supply before starting work.
• Drain remaining water from the line and place a towel or tray to catch drips.
• Inspect connection fittings and any O-rings; replace seals if damaged to prevent leaks.
• After installation, restore water and power, then check all connections carefully for leaks.

User interface provides the control surface and display for selecting cycles, options and viewing status. Replaces a worn or unresponsive control to restore user access and visible cycle feedback. What it does:

• Lets you choose cycles, options and settings via the control buttons/touch surface.
• Displays cycle status, time remaining and status/error indicators.
• Replaces cracked, unresponsive or intermittently-working control surfaces.
• Can address symptoms such as unresponsive buttons, blank/erratic display, or controls that don't register inputs.

• Always disconnect power before attempting any service to avoid shock.
• Remove the control console or access panel; handle ribbon cables and connectors gently.
• Reconnect all connectors securely and test the interface before reassembling panels.

This retainer is a small mounting clip that secures internal components and trim to keep panels and assemblies aligned during normal use. It restores secure fitment and reduces movement or rattling from loose parts. What it does:

• Holds panels, trim, or small assemblies in place to prevent shifting and vibration
• Helps stop rattling or buzzing caused by loose internal components
• Keeps parts aligned so doors, drawers, or panels operate smoothly
• Replaces cracked, broken, or worn clips that no longer grip reliably

• Disconnect power to the appliance before inspecting or replacing parts
• Remove surrounding panels or trim as needed to access the retainer; keep screws/fasteners for reassembly
• Snap the clip into the mating slot or tab until it seats; replace any damaged mounting points
• Replace all adjacent clips for consistent fit

The Motor Mount Bushing is an essential OEM component inside Frigidaire bottom-mount refrigerators. It secures the evaporator fan motor securely while cushioning vibrations transmitted to the refrigerator body.  

Causes of failure include natural wear of plastic glide surfaces from prolonged absorption of mechanical stresses during compressor and fan operation cycles. Deformations compromise uniform motor positioning over time.

Symptoms of a worn motor mount bushing include:

• Rattling noises emanating from the refrigerator fan area
• Reduced air circulation leading to warmer interior temperatures 
• Lubricant leaks at the mounting point requiring replacement

This authentic OEM replacement is compatible with Frigidaire, Electrolux and select Kenmore models.

The Slide Assembly is an essential OEM component for Frigidaire refrigerator drawers. It provides smooth extension and retraction of covered storage bins during access.  

Symptoms of a faulty slide assembly include:

• Squeaking or rubbing noises coming from drawer rails   
• Difficulty smoothly pulling out covered bins
• Scratches or gouges visible along wear surfaces

Causes involve years of constant sliding stresses overwhelming lubrication, leading to increased friction. Without smooth gliding, premature deterioration of plastic drawer supports results.

This authentic OEM replacement is compatible with Frigidaire, Electrolux, and Kenmore models.

Control assembly that replaces a faulty front control, restoring touchpad and display responsiveness so the range or oven accepts commands and shows status. What it does:

• Replaces the appliance's front user interface, including the touchpad/keys and display electronics.
• Restores ability to enter settings, start cycles and change functions when the original control is unresponsive.
• Commonly used when the display is blank, shows garbled characters, or button presses do not register.
• Matches the appliance only if the part number fits.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Handle the control assembly by its edges and avoid contact with circuits; use ESD precautions if available.
• Installation typically requires removing the control panel or backguard and unplugging/replugging the wire harness; retain all mounting hardware.