Fghd4261kw1 Parts

Filter only. Fine filter not included.

This thermostat assembly regulates refrigerator temperature, helping maintain set cooling levels for fresh food or freezer sections. It replaces a faulty control that can cause inconsistent temperatures or erratic compressor cycling. What it does:

• Senses internal temperature and signals the compressor to run or stop to maintain setpoint
• Restores stable cooling when a failed thermostat causes warm spots or fluctuating temps
• Stops excessive compressor cycling caused by a defective control
• Works with the fridge's temperature knob/sensor system to provide user temperature adjustments

• Disconnect power before starting; shut off water/ice features if applicable
• Handle the capillary tube and sensor gently—do not kink or bend sharply
• Match mounting orientation and electrical connector locations to the original part
• After installation, restore power and verify proper temperature control and normal compressor cycling

This duct assembly channels air through the appliance to maintain proper airflow and reliable operation. Replacing a damaged or cracked duct helps restore ventilation and can reduce noise and poor performance. What it does:

• Directs air from the blower/tub area into the vent path to enable normal airflow
• Prevents leaks that can reduce drying/cooling efficiency or cause longer cycles
• Helps reduce vibration and rattling caused by a loose or broken duct
• Common symptom: reduced airflow, longer cycle times, or unusual noise during operation

• Disconnect power to the appliance before beginning any repair
• Inspect surrounding seals and mounting tabs; replace any damaged hardware
• Basic hand tools required; handle carefully to avoid cracking plastic tabs

This upper hinge cover protects and finishes the refrigerator door hinge area on the right side, restoring appearance and helping keep hinge components free of dust and debris. Designed as a direct replacement for the OEM right-side hinge cover. What it does:

• Covers the upper door hinge area to improve cosmetic appearance and hide hardware
• Helps keep dust, crumbs, and moisture away from hinge components
• Prevents accidental contact with hinge edges while opening and closing the door
• Restores the original look after hinge repairs or replacements

• One upper hinge cover for the right (RH) side, gray

• Disconnect power to the appliance or unplug before servicing to prevent electrical hazards
• Handle carefully to avoid scratching the finish; align clip/fastener locations before snapping into place

This console assembly replaces the dryer control console to restore a secure housing for the buttons, knobs and display, improving user access and protecting the controls from damage. Fits as a direct replacement when the original console is cracked or worn. What it does:

• Houses and protects the control buttons, knobs and display so controls operate reliably
• Provides the correct mounting and alignment for control components and user interface
• Helps resolve issues like cracked or loose front panel, exposed wiring, or inaccessible controls
• Restores a finished appearance to the appliance front

• Disconnect power before starting and follow all manufacturer safety instructions
• Removal typically requires accessing fasteners behind the top panel and carefully detaching any ribbon or wiring harnesses
• Handle attached wiring and switches gently; confirm connector positions before reassembly

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This door gasket seals the refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn, torn, or compressed seal to improve cooling performance and food safety. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in and warm air out
• Helps prevent frost build-up and reduces moisture inside the compartment
• Can stop visible gaps that allow warm air and odors to enter
• Restores consistent temperatures for better food preservation

• One refrigerator door gasket

• Handle gently to avoid stretching or tearing; follow the appliance manufacturer's alignment and fastening steps
• Clean the door flange and gasket channel before installation for a proper seal
• Some gaskets require heating (hair dryer) or a short break-in period to fully seat; follow your model's instructions

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions

This replacement nameplate label restores the appliance's identification and rating information so you can read model, serial, and electrical data clearly. Helps when the original label is faded, damaged, or missing. What it does

• Displays model and serial numbers, electrical ratings and safety markings for identification and service
• Replaces faded, torn, or illegible factory labels so appliance data is readable
• Helps technicians and owners confirm correct specifications during repairs or replacement parts ordering
• Does not affect appliance operation; used for identification and information only

• One replacement nameplate label

• Clean and dry the surface before applying so the label adheres and lays flat
• Align carefully; many labels are adhesive-backed and are intended for single use
• Avoid placing over gaskets, vents, or moving parts; install where original label was located

This mounting bracket secures appliance components to the cabinet frame, restoring solid support and alignment. It's a straightforward replacement for worn, bent, or broken brackets that cause loose panels or misaligned doors. What it does:

• Provides structural support for interior or exterior panels and components
• Helps stop rattling or vibration caused by a loose or damaged bracket
• Restores proper alignment to doors or trim that shift due to bracket failure
• Used wherever a small metal bracket fastens parts to the appliance frame

• One mounting bracket

• Disconnect power to the appliance before servicing to avoid shock or injury
• Installation typically requires basic hand tools; keep fasteners for reuse unless replacement specified
• Handle edges and metal parts carefully to avoid cuts; consider gloves

This genuine replacement screw secures appliance panels and components so assemblies stay tight and stable. It's a simple, direct fix when a missing or damaged screw causes loose trim, rattling, or misaligned parts. What it does:

• Fastens panels, brackets, and trim to restore proper alignment and stability
• Stops rattling or vibration caused by loose hardware
• Replaces stripped or corroded screws to ensure secure connections
• Works wherever the OEM screw is specified in the appliance

• Use the matching driver and proper torque to avoid stripping the head or threads
• Replace only with the exact OEM screw to maintain fit and function
• Disconnect power before accessing internal components; follow appliance safety instructions
• Replace all like-for-like for best results

This complete door assembly replaces a damaged or worn oven/microwave door to restore proper closing, safety, and appearance. It provides a ready-to-install replacement that helps maintain heat containment and safe operation. What it does:

• Replaces a cracked, dented, or warped door to restore a secure seal and proper latching
• Helps stop heat or steam from escaping during cooking, improving performance
• Restores the appliance's exterior appearance and protects internal components
• Corrects alignment and closing issues caused by bent or broken door components

• One complete door assembly as shown

• Disconnect power and allow the appliance to cool before starting any work
• Door assemblies can be heavy or awkward—use a second person to help hold and align during installation
• Follow the appliance manufacturer's service instructions and retain all original fasteners and brackets where required
• If the door contains glass, handle carefully to avoid breakage and wear protective gloves and eye protection