Fghf2369mf6 Serial Parts

This small rubber bumper cushions the refrigerator/freezer door to reduce noise and prevent metal-on-metal contact. It helps doors close quietly and protects cabinet finish from repeated impacts. What it does:

• Acts as a soft stop between the door and cabinet/frame to absorb impact
• Reduces rattling and slamming for quieter operation
• Prevents wear and chipping where the door contacts the cabinet
• Restores proper door alignment when missing or worn

• One replacement bumper

• Push the bumper into the existing hole or slot on the door/frame until fully seated
• Inspect surrounding area for damage; replace mounting clips or retainers if required
• Wear gloves to protect hands from sharp edges during installation
• No special tools usually required; for detailed instructions

This air handler housing is the molded cabinet that supports and protects the blower and internal air-handling components, helping direct airflow and maintain proper alignment for reliable cooling and heating performance. What it does:

• Forms the structural enclosure for the blower/air handler assembly and related components
• Channels and directs airflow through the evaporator and into the ductwork
• Helps maintain component alignment to prevent rubbing, vibration, and airflow loss
• Can reduce air leaks and restore proper circulation when a cracked or damaged housing causes performance issues

• Intended for technicians or experienced DIYers; disconnect power before starting work
• Remove surrounding panels and note screw/clip locations to ensure correct reassembly
• Inspect adjacent parts (blower wheel, seals, mounting tabs) and replace if damaged
• Use care to avoid cracking plastic during removal and reinstallation; do not force parts into place

This tube adapter connects and seals a refrigerator water line to the inlet or valve, restoring a secure water pathway for the ice maker or dispenser. Use it to stop leaks and re-establish reliable water flow. What it does

• Adapts and secures the appliance water tube to the inlet or valve, forming a leak-proof connection
• Restores proper water feed to the ice maker and/or water dispenser when the original adapter is damaged
• Helps prevent drips or steady leaks at the tube connection
• Works with standard refrigerator water tubing and compression fittings where specified

• One tube adapter

• Turn off the refrigerator power and shut off the household water supply before starting
• Remove the damaged adapter and clean tube ends; replace with this adapter using appropriate compression or push-fit method
• Tighten fittings to a snug, leak-free fit; avoid over-tightening plastic parts
• After installation, restore water and power, and check thoroughly for leaks

This beam-style crisper cover is the glass shelf that sits above the crisper drawer, providing a flat support surface and helping contain spills while keeping produce organized. It restores the shelf surface and proper crisper function. What it does:

• Replaces a broken or missing crisper cover to restore a stable shelf over the crisper drawer
• Helps contain spills and prevents items from falling into the crisper
• Supports produce and other refrigerated items above the drawer area
• Works with the refrigerator's crisper beam/track system to maintain proper clearance and operation

• One crisper cover (beam-style) as shown

• Always unplug the refrigerator or shut off power before servicing interior components
• Remove food and any items from the shelf area before installation
• Handle the glass carefully; lift straight up/out from the tracks or supports and slide the replacement into position
• If the cover uses plastic clips or rails, inspect and replace damaged hardware to ensure a secure fit

This water filter housing is the refrigerator-mounted enclosure that holds and seals the replaceable water filter cartridge, helping ensure proper water flow to the dispenser and icemaker. Fits factory filter systems and restores secure filter seating. What it does:

• Houses and secures the refrigerator water filter cartridge to maintain a sealed water path
• Directs filtered water to the dispenser and icemaker while preventing leaks when installed correctly
• Can help stop water bypass or weak flow caused by damaged or cracked housings
• Supports proper alignment for O-rings and filter locking/engagement

• One water filter housing designed for the factory filter location

• Turn off the refrigerator water supply and dispense any residual water before servicing
• Remove power to the appliance if required by your model and follow manufacturer safety guidance
• Inspect and replace associated O-rings or seals if worn; confirm proper seating to prevent leaks

This slide replaces a worn or broken drawer support to restore smooth, stable drawer movement and secure shelf alignment. Durable replacement designed to match the OEM fit and function for proper drawer operation. What it does:

• Supports and guides a refrigerator/freezer drawer or shelf for smooth in-and-out motion
• Restores proper alignment when drawers stick, drag, or sit unevenly
• Prevents drawers from falling out or binding during use
• Reduces noise caused by worn or damaged sliding tracks

• Always unplug the appliance or switch off power before servicing to avoid electrical hazard
• Remove the drawer or shelf to access mounting screws and clips before replacing the slide
• Compare the new slide to the original to ensure correct orientation and fastener locations
• Use common hand tools; do not force parts—if mounting holes don't line up, stop and verify part compatibility

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim

This molded evaporator cover replaces the plastic trim that protects and directs airflow over the freezer evaporator; it helps maintain even cooling and keeps ice and debris away from the coil assembly. Fits the OEM mounting locations for a proper seal. What it does

• Protects the evaporator coil from loose food and debris that can impede airflow.
• Directs cold air through the freezer compartment for more consistent temperatures.
• Helps reduce frost build-up on the evaporator by maintaining proper airflow patterns.
• Restores proper fit and appearance where the original cover is cracked, warped, or missing.

• One evaporator cover

• Disconnect power to the appliance before starting any repair.
• Remove screws or fasteners holding the old cover; handle tabs carefully to avoid breaking mounting clips.
• Defrost and dry the area if there is ice buildup before installing the new cover.
• Reassemble panels and verify there are no gaps that could allow air leaks or contact with moving components.

This H-shaped evaporator gasket creates a tight seal around the evaporator housing to help control airflow and reduce frost buildup in the freezer compartment. It replaces a worn or cracked gasket to restore proper cooling performance. What it does

• Seals the evaporator housing to prevent warm, moist air from entering the evaporator area.
• Helps maintain consistent airflow over the evaporator for efficient defrosting and cooling.
• Reduces frost and ice buildup caused by gaps or leaks around the evaporator.
• Commonly used when you see excessive frost, poor cooling, or visible gasket damage near the evaporator.

• One H-shaped evaporator gasket.

• Disconnect power to the appliance before starting any repair.
• Remove freezer panels and the evaporator cover to access the gasket; handle evaporator fins carefully to avoid damage.
• Clean mating surfaces and remove old adhesive or residue before installing the new gasket for a proper seal.
• If adhesive is required, use a refrigerator-safe sealant recommended by the manufacturer.

This shelf channel mounting bracket secures the shelf channel to the appliance cabinet so shelves stay level and stable. It replaces a broken or worn mount to restore proper shelf alignment and support. What it does

• Secures the shelf channel to the cabinet frame so shelves sit flush and don't tilt.
• Prevents shelf movement or sagging caused by a loose or cracked mount.
• Helps maintain safe storage by keeping items from sliding off tilted shelves.
• Fits where the original channel mount has cracked, worn, or snapped.

• Designed for simple replacement—remove the shelf and channel to access the mounting bracket.
• Use appropriate hand tools; avoid over-tightening fasteners which can crack plastic components.
• Disconnect power and remove stored items from the shelf area before beginning work.
• If mounting locations are damaged, assess surrounding supports; replace any additional broken hardware.

This housing is the replacement cabinet housing that provides structural support and protects internal components, restoring proper fit and appearance. It helps stabilize assemblies and keeps wiring and parts shielded from damage. What it does:

• Replaces a cracked, broken, or dented cabinet housing to restore structural integrity
• Protects internal components and wiring from debris and accidental contact
• Helps reduce rattling or movement caused by damaged housing
• Restores the appliance's proper fit and alignment for panels and doors

• One housing

• Disconnect power to the appliance before starting any repair
• Use appropriate hand tools; support adjacent panels to avoid stress on clips or fasteners
• Watch for sharp edges; wear gloves and eye protection

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

This condenser tube spacer positions and secures the refrigerator's condenser tubing to maintain proper tube spacing and airflow. Replacing a worn or broken spacer helps reduce vibration, rattling, and rubbing that can damage tubing over time. What it does:

• Holds condenser tubing in the correct position to preserve airflow and cooling efficiency
• Cushions tubing to limit vibration and reduce rattling noises
• Prevents tubing from rubbing against the cabinet or other components, lowering wear risk
• Helps reduce the chance of tubing fatigue that can lead to damage

• Disconnect power to the appliance before accessing rear panels or condenser components.
• Handle condenser tubing gently; avoid kinking, bending, or putting stress on lines during installation.
• Installation may require removing the back or lower access panel to reach the condenser assembly.

A replacement bushing that supports a rotating shaft and reduces wear between moving metal parts, restoring smooth, quiet operation. Fits OEM specification to ensure proper alignment and long-lasting performance. What it does:

• Cushions and guides a rotating shaft or drum to prevent metal-on-metal contact
• Reduces noise, vibration, and wobble caused by worn support surfaces
• Helps maintain proper shaft/drum alignment for even operation
• Limits premature wear to adjacent bearings, seals, and housing

• One bushing

• Disconnect power before starting any repair and follow OEM disassembly instructions
• Replacement typically requires access to the motor/shaft or drum housing; some disassembly may be necessary
• Inspect adjacent bearings and seals and replace if worn to prevent repeat failures