Fghs2355pf Parts

This refrigerator water inlet tube channels water from the valve into the internal dispensing/ice system. Replace a cracked, kinked, or clogged tube to restore proper flow and help stop leaks at the rear or inside the cabinet.

• Routes water from the inlet valve to the refrigerator's water system
• Helps resolve leaks, weak/no dispenser flow, or no ice production due to damaged or restricted tubing
• Replaces brittle, cracked, or kinked tubing that can cause drips or water damage
• Maintains a sealed path when properly seated in the existing fittings

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel/pan to catch residual water
• Note the original routing; transfer any reusable clips/fittings from the old tube
• Cut ends square if required, push fully into couplers, restore water, and check carefully for leaks before reconnecting power

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

Color: Stainless Steel
The Dispenser Trim is an OEM part for Frigidaire refrigerators. It surrounds the ice and water dispenser area located externally on the refrigerator door.

Causes of a faulty dispenser trim can include cracks, chips or damage from impacts or general wear over time.

Symptoms of failure include:

• Water leaks developing around the dispenser opening
• Loose or detached trim that does not sit flush
• Access to dispenser functions being obstructed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator water tank (reservoir) stores and chills drinking water inside the fresh food compartment, helping deliver a steady, reliable stream to the dispenser. Replace a cracked or leaking tank to stop interior leaks and restore dispenser performance.

• Stores a small volume of drinking water so it's cooled before dispensing
• Helps maintain consistent dispenser flow by buffering line pressure
• A cracked tank can leak water inside the fresh food section, often under the crisper drawers
• A restricted or frozen tank can cause little or no water, or sputtering, from the dispenser

• Unplug the refrigerator and shut off the household water supply; depressurize by dispensing water
• Access the tank, typically behind the lower crisper drawers in the fresh food section; place towels to catch residual water
• Reconnect existing water lines using push-to-connect fittings; cut tubing square and fully seat it
• Restore water and power, check for leaks at all connections, and flush the water system thoroughly

Restore stable storage and help contain leaks with this Spill Safe Shelf. Replacing a cracked or missing shelf brings back usable space and helps prevent spills from dripping onto lower shelves and drawers.

• Supports food and containers on the designated refrigerator level
• Spill Safe design helps contain minor leaks to the shelf area
• Replace if the shelf is cracked, warped, loose, or missing
• Common symptoms: drips reaching lower shelves, shelf no longer seating correctly, reduced storage capacity

• Remove all items from the shelf area before replacement
• Slide the old shelf out; align the rear of the new shelf with the slots/rails, then lower the front until fully seated
• Do not force into place; use the correct rail position for your model
• Handle with both hands to avoid dropping or damaging the shelf

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This door-activated light switch controls the interior refrigerator lighting, turning the light on when the door opens and off when it closes. Replacing a faulty switch restores proper lighting and helps prevent the light from staying on and warming the compartment.

• Opens/closes the light circuit based on door position
• Helps if the interior light won't turn on with the door open
• Fixes lights that stay on with the door closed
• Addresses intermittent or stuck plunger operation
• Restores normal visibility inside the refrigerator

• Disconnect power before servicing to avoid electrical shock
• Access the switch at the door liner or control housing; release tabs or screws as applicable
• Note wire positions, then transfer wires to the new switch one at a time
• The switch plunger moves freely and the light turns off with the door closed

Lower hinge secures the bottom corner of a refrigerator door and provides a durable pivot for smooth opening and closing. Replacing a worn hinge restores proper door alignment and helps maintain a tight seal. What it does:

• Supports the weight of the lower door corner and provides a pivot point for opening/closing.
• Keeps the door aligned so the gasket can seal properly.
• Worn or damaged hinges can cause door sag, uneven gaps, rubbing, or difficulty closing.
• Restoring a solid hinge reduces stress on the door and latch for more reliable operation.

• Disconnect power to the appliance and remove food/items from the door before starting.
• Always support the door while removing/installing the hinge to prevent dropping or damage.
• Use the correct tools and hardware; tighten fasteners snugly but avoid over-torquing.
• After installation, check door alignment and seal; adjust as needed for proper operation.

Right side.

This control rod spring fits the refrigerator's ice maker shutoff arm. It restores proper tension so the ice maker cycles on/off correctly and stops making ice when the bucket is full.

• Maintains tension on the ice maker control/shutoff arm for reliable on/off operation
• Helps the arm return to position so the ice maker senses a full bin and pauses production
• A weakened or missing spring may cause an overfilling ice bucket, a loose arm, or inconsistent ice production
• Replaces damaged or stretched springs that prevent the control rod from moving smoothly

• Unplug the refrigerator and shut off water to the ice maker
• Empty the ice bin and access the shutoff arm pivot
• Note the spring's orientation; install with needle-nose pliers without bending the control rod
• Restore power/water and verify smooth arm movement and proper shutoff

This electronic power control board manages incoming power and directs it to the refrigerator's compressor, fans, and control circuits. Replacing a failed board can help restore cooling performance and bring unresponsive or intermittently running units back to normal operation.

• Distributes and regulates power for the compressor and fan motors; failure can leave the unit warm or silent
• Sequences cooling operations based on sensor/control inputs; faults may cause intermittent starting or frequent power cycling
• Interfaces with the refrigerator's controls to execute cooling commands; issues can present as an unresponsive control panel
• Contains relays and protective circuitry; burn marks or repeated relay clicking can indicate a defective board

• Disconnect power before service; use anti-static (ESD) precautions when handling the board
• Board is typically located at the back of the refrigerator in the machine compartment behind the rear access panel
• Photograph wiring; move connectors and any jumpers to the new board, matching positions and orientation
• Ensure all plugs are fully seated, reassemble, restore power, and allow up to 24 hours for temperatures to stabilize

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used